Gate design and filling process analysis of the cavity in injection molding process
Received date: 2015-06-28
Revised date: 2016-03-28
Online published: 2016-06-25
This paper presents a new geometry of an edge gate in the injection molding process called modified edge gate. The corners of current edge gate result in the turbulence of molten plastic into the cavity which leads to internal and external defects. The aim of the new geometry is to reduce the internal and external defects of injected part such as sink marks and short shot. The easier de-gating analysis for the new geometry to decrease the visible blemish of the injected part was proposed in this study. A modified edge gate was proposed for two circular flat plates with thickness 1 mm. Finite element method (FEM) was used along with SolidWorks plastic. Internal and external defects of the injected part were analyzed via SolidWorks plastic. To validate the new geometry, an experimental study was implemented for two polypropylene (PP) circular flat plates with modified edge gate to confirm the simulation results. The contribution of this research is to modify the geometry of current edge gate by removing the corners of rectangular edge gate which leads to the reduction of scrap. The new geometry presents easier degating of gate and less visible blemish of the injected part. A smooth flow of molten plastic into the cavities reduces the internal and external defects. The outcome of this study demonstrates filling of the cavities with no short shot. In addition, no sink marks were detected with modified edge gate. Finally, the modified edge gate has less visible blemish on the injected part in comparison with current edge gate.
Key words： Injection molding; Gate design; Internal defects; External defects
Mehdi Moayyedian , Kazem Abhary , Romeo Marian . Gate design and filling process analysis of the cavity in injection molding process[J]. Advances in Manufacturing, 2016 , 4(2) : 123 -133 . DOI: 10.1007/s40436-016-0138-5
1. Salimi A et al (2013) Prediction of flow length in injection molding for engineering plastics by fuzzy logic under different processing conditions. Iran Polym J 22(1):33-41
2. Zhou H (2012) Computer modeling for injection molding:simulation, optimization, and control. Wiley, Hoboken
3. Tang SH, Kong YM, Sapuan SM et al (2006) Design and thermal analysis of plastic injection mould. J Mater Process Technol 171(2):259-267
4. Pirc N, Schmidt F, Mongeau M et al (2009) Optimization of 3D cooling channels in injection molding using DRBEM and model reduction. Int J Mater Form 2(5):271-274
5. Subramanian NR, Tingyu L, Seng YA (2005) Optimizing warpage analysis for an optical housing. Mechatronics 15:111-127
6. Altan M (2010) Reducing shrinkage in injection moldings via the Taguchi, ANOVA and neural network methods. Mater Des 31(1):599-604
7. Dimla D, Camilotto M, Miani F (2005) Design and optimisation of conformal cooling channels in injection moulding tools. J Mater Process Technol 164:1294-1300
8. Agazzi A, Sobotka V, Goff RL et al (2010) A methodology for the design of effective cooling system in injection moulding. Int J Mater Form 3:13-16
9. Rutkauskas ?, Bargelis A (2007) Knowledge-based method for gate and cold runner definition in injection mold design. MECHANIKA, ISSN, pp 1392-1207
10. Gokey J, Harris T (2004) An investigation into the gate location and its effects on product quality in injection molding. In:Annual technical conference-ANTEC, Conference Proceedings. Society of Plastics Engineers, Chicago
11. Lee KS, Lin JC (2006) Design of the runner and gating system parameters for a multi-cavity injection mould using FEM and neural network. Int J Adv Manuf Technol 27:1089-1096
12. Huang MC, Tai CC (2001) The effective factors in the warpage problem of an injection-molded part with a thin shell feature. J Mater Process Technol 110:1-9
13. Kima HS, Sonb JS, Imc YT (2003) Gate location design in injection molding of an automobile junction box with integral hinges. J Mater Process Technol 140:110-115
14. Jones P (2015) Mould design guide
15. Calhoun DAR, Golmanavich J (2002) Plastics technician's toolbox-extrusion-fundamental skills and polymer science. Ron Jon, Addison
16. Shen C, Wang L, Cao W et al (2007) Investigation of the effect of molding variables on sink marks of plastic injection molded parts using Taguchi DOE technique. Polym Plast Technol Eng 46(3):219-225
17. Oktem H, Erzurumlu T, Uzman I (2007) Application of Taguchi optimization technique in determining plastic injection molding process parameters for a thin-shell part. Mater Des 28:1271-1278
18. Yang K, El-Haik BS (2009) Design for six sigma:a roadmap for product development. McGraw-Hill Companies, New York
19. Dai W, Liu P, Wang X (2002) An improved mold pin gate and its flow pattern in the cavity. J Inject Molding Technol 6(2):115
20. Beaumont JP (2004) Runner and gating design handbook. Hanser, Munich
21. Goodship V (2004) Troubleshooting injection moulding, vol 15. iSmithers Rapra Publishing
22. Pye R (1989) Injection mold design:a textbook for the novice and a design manual for the thermoplastics industry. Wiley, New York
/
| 〈 |
|
〉 |
