A structural model of a soft/hard compositecoated textured (SHCCT) tool was proposed and substantiated by a three-dimensional numerical simulation. Its dry turning performance as applied to AISI-1045 steel was analyzed via three-factor five-level orthogonal experiments for different coating parameters, including coating thickness, coating material, and thickness ratio of the soft and hard coatings. In addition, the cutting performance of the proposed SHCCT tool was compared with those of uncoated non-textured, coated non-textured, and uncoated textured tools, and its superiority was proved by the significant reductions in the cutting force, and specifically, the cutting temperature. The optimal results were provided by the SHCCT tool with a WS2/ZrN soft/hard composite coating, a 0.9:0.1 thickness ratio of the above ingredients, and a total coating thickness of 0.5 μm.
The full text can be downloaded at https://link.springer.com/article/10.1007/s40436-019-00249-2
Yun-Song Lian
,
Chen-Liang Mu
,
Ming Liu
,
Hui-Feng Chen
,
Bin Yao
. Three-dimensional numerical simulation of soft/hard composite-coated textured tools in dry turning of AISI 1045 steel[J]. Advances in Manufacturing, 2019
, 7(2)
: 133
-141
.
DOI: 10.1007/s40436-019-00249-2
1. Debnath S, Reddy MM, Yi QS (2016) Influence of cutting fluid conditions and cutting parameters on surface roughness and tool wear in turning process using Taguchi method. Measurement 78:111-119
2. Yasar HS, Heris SZ, Shanbedi M et al (2017) Experimental investigation of thermal properties of cutting fluid using soluble oil-based TiO2 nanofluid. Powder Technol 310:213-220
3. Paul PS, Varadarajan AS, Gnanadurai RR (2016) Study on the influence of fluid application parameters on tool vibration and cutting performance during turning of hardened steel. Eng Sci Technol Int J 19(1):241-253
4. Feng WL, Yin Y, Mendoza ML et al (2018) Oil recovery from waste cutting fluid via the combination of suspension crystallization and freeze-thaw processes. J Clean Prod 172:481-487
5. Uddin MS, Pham B, Sarhan A et al (2017) Comparative study between wear of uncoated and TiAlN-coated carbide tools in milling of Ti6Al4V. Adv Manuf 5(1):83-91
6. Ma JF, Duong NH, Chang S et al (2015) Assessment of microgrooved cutting tool in dry machining of AISI 1045 steel. ASME J Manuf Sci Eng 137(3):031001
7. Sugihara T, Singh P, Enomoto T (2017) Development of novel cutting tools with dimple textured surfaces for dry machining of aluminum alloys. Procedia Manuf 14:111-117
8. Azarhoushang B, Zahedi A (2017) Laser conditioning and structuring of grinding tools-a review. Adv Manuf 5(1):35-49
9. Kumar CS, Patel SK (2018) Effect of WEDM surface texturing on Al2O3/TiCN composite ceramic tools in dry cutting of hardened steel. Ceram Int 44(2):2510-2523
10. Kumar R, Sahoo AK, Mishra PC et al (2018) Comparative investigation towards machinability improvement in hard turning using coated and uncoated carbide inserts:part I. Experimental investigation. Adv Manuf 6(1):52-70
11. Prengel HG, Jindal PC, Wendt KH et al (2001) A new class of high performance PVD coatings for carbide cutting tools. Surf Coat Technol 139(1):25-34
12. Xie J, Luo MJ, Wu KK et al (2013) Experimental study on cutting temperature and cutting force in dry turning of titanium alloy using a non-coated micro-grooved tool. Int J Mach Tools Manuf 73:25-36
13. Kümmel J, Braun D, Gibmeier J et al (2015) Study on micro texturing of uncoated cemented carbide cutting tools for wear improvement and built-up edge stabilisation. J Mater Process Technol 215:62-70
14. Deng JX, Song WL, Zhang H et al (2008) Performance of PVD MoS2/Zr-coated carbide in cutting processes. Int J Mach Tools Manuf 48(14):1546-1552
15. Aslantas K, Ucun İ, Çicek A (2012) Tool life and wear mechanism of coated and uncoated Al2O3/TiCN mixed ceramic tools in turning hardened alloy steel. Wear 274-275:442-451
16. Vasumathy D, Meena A (2017) Influence of micro scale textured tools on tribological properties at tool-chip interface in turning AISI 316 austenitic stainless steel. Wear 376-377:1747-1758
17. Kawasegi N, Sugimori H, Morimoto H et al (2009) Development of cutting tools with microscale and nanoscale textures to improve frictional behaviour. Precis Eng 33(3):248-254
18. Lian YS, Deng JX, Li SP et al (2013) Preparation and cutting performance of WS2 soft-coated tools. Int J Adv Manuf Technol 67(5-8):1027-1033
19. Nouari M, Ginting A (2006) Wear characteristics and performance of multi-layer CVD-coated alloyed carbide tool in dry end milling of titanium alloy. Surf Coat Technol 200(18-19):5663-5676
20. Arulkirubakaran D, Senthilkumar V, Kumawat V (2016) Effect of micro-textured tools on machining of Ti-6Al-4V alloy:an experimental and numerical approach. Int J Refract Metals Hard Mater 54:165-177
21. Kim DM, Bajpai V, Kim BH et al (2015) Finite element modeling of hard turning process via a micro-textured tool. Int J Adv Manuf Technol 78(9-12):1393-1405
22. Chen RY (1993) Metal-cutting principles. China Machine Press, Beijing
23. Loewen E, Shaw M (1954) On the analysis of cutting tool temperatures. Trans ASME 76(2):217-225
24. Bono M, Ni J (2006) The location of the maximum temperature on the cutting edges of a drill. Int J Mach Tools Manuf 46(7-8):901-907
