The purpose of this study was to develop a closed-loop machine vision system for wire electrical discharge machining (EDM) process control. Excessive wire wear leading to wire breakage is the primary cause of wire EDM process failures. Such process interruptions are undesirable because they affect cost efficiency, surface quality, and process sustainability. The developed system monitors wire wear using an image-processing algorithm and suggests parametric changes according to the severity of the wire wear. Microscopic images of the wire electrode coming out from the machining zone are fed to the system as raw images. In the proposed method, the images are pre-processed and enhanced to obtain a binary image that is used to compute the wire wear ratio (WWR). The input parameters that are adjusted to recover from the unstable conditions that cause excessive wire wear are pulse off time, servo voltage, and wire feed rate. The algorithm successfully predicted wire breakage events. In addition, the alternative parametric settings proposed by the control algorithm were successful in reducing the wire wear to safe limits, thereby preventing wire breakage interruptions.
The full text can be downloaded at https://link.springer.com/article/10.1007/s40436-021-00373-y
P. M. Abhilash
,
D. Chakradhar
. Machine-vision-based electrode wear analysis for closed loop wire EDM process control[J]. Advances in Manufacturing, 2022
, 10(1)
: 131
-142
.
DOI: 10.1007/s40436-021-00373-y
1. Ho KH, Newman ST, Rahimifard S et al (2004) State of the art in wire electrical discharge machining (WEDM). Int J Mach Tools Manuf 44(12/13):1247-1259
2. Mandal A, Dixit AR (2014) State of art in wire electrical discharge machining process and performance. Int J Mach Manu Mater 16(1):1-21
3. Ramakrishnan R, Karunamoorthy L (2008) Modeling and multi-response optimization of Inconel 718 on machining of CNC WEDM process. J Mater Process Technol 207:343-349
4. Mandal A, Dixit AR, Das AK et al (2016) Modeling and optimization of machining nimonic C-263 superalloy using multicut strategy in WEDM. Mater Manuf Process 31:860-868
5. Manjaiah M, Laubscher RF, Kumar A et al (2016) Parametric optimization of MRR and surface roughness in wire electro discharge machining (WEDM) of D2 steel using taguchi-based utility approach. Int J Mech Mater Eng 11(7):1-9
6. Senkathir S, Aravind R, Samson RM et al (2019) Optimization of machining parameters of Inconel 718 by WEDM using response surface methodology. Adv Manuf Process 37:383-392
7. Bergs T, Tombul U, Herrig T et al (2018) Analysis of characteristic process parameters to identify unstable process conditions during wire EDM. Procedia Manuf 18:138-145
8. Gamage JR, Desilva AKM (2016) Effect of wire breakage on the process energy utilisation of EDM. Procedia CIRP 42:586-590
9. Kawata A, Okada A, Okamoto Y et al (2017) Influence of nozzle jet flushing on wire breakage in 1st-cut wire EDM from start hole. Key Eng Mater 749:130-135
10. Melnik Y, Kozochkin M, Porvatov A et al (2018) On adaptive control for electrical discharge machining using vibroacoustic emission. Technologies 6:96-114
11. Kwon S, Yang MY (2006) The benefits of using instantaneous energy to monitor the transient state of the wire EDM process. Int J Adv Manuf Technol 27:930-938
12. Yan MT, Liao YS (1996) A self-learning fuzzy controller for wire rupture prevention in WEDM. Int J Adv Manuf Technol 11:267-275
13. Yan MT, Liao YS (1998) Adaptive control of the WEDM process using the fuzzy control strategy. J Manuf Syst 17:263-274
14. Liao YS, Woo JC (2000) Design of a fuzzy controller for the adaptive control of WEDM process. Int J Mach Tools Manuf 40:2293-2307
15. Bufardi A, Akten O, Arif M et al (2017) Towards zero-defect manufacturing with a combined online-offline fuzzy-nets approach in wire electrical discharge machining. WSEAS Trans Environ Dev 13:401-409
16. Caggiano A, Teti R, Perez R et al (2015) Wire EDM monitoring for zero-defect manufacturing based on advanced sensor signal processing. Procedia CIRP 33:315-320
17. Cabanes I, Portillo E, Marcos M et al (2008) On-line prevention of wire breakage in wire electro-discharge machining. Robot Comput Integr Manuf 24:287-298
18. Klocke F, Welling D, Klink A et al (2014) Quality assessment through in-process monitoring of wire-EDM for fir tree slot production. New Prod Technol Aerosp Ind-5th Mach Innov Conf (MIC 2014)-Procedia CIRP 24:97-102
19. Abhilash PM, Chakradhar D (2021) Chakradhar image processing algorithm for detection quantification and classification of microdefects in wire electric discharge machined precision finish cut surfaces. J Micromanuf. https://doi.org/10.1177/25165984211015410
20. Martínez SS, Vázquez CO, García JG et al (2015) Image fusion for surface finishing inspection. Int Conf Imaging Syst Tech Proc 2015:3-8
21. Frayman Y, Zheng H, Nahavandi S (2006) Machine vision system for automatic inspection of surface defects in aluminum die casting. J Adv Comput Intell Intell Informatics 10:281-286
22. Steiner D, Katz R (2007) Measurement techniques for the inspection of porosity flaws on machined surfaces. J Comput Inf Sci Eng 7:85-94
23. Khalifa OO, Densibali A, Faris W (2006) Image processing for chatter identification in machining processes. Int J Adv Manuf Technol 31:443-449
24. Manish R, Venkatesh A, Denis AS (2018) Machine vision based image processing techniques for surface finish and defect inspection in a grinding process. Mater Today Proc 5:12792-12802
25. Zhang C, Zhang J (2013) On-line tool wear measurement for ball-end milling cutter based on machine vision. Comput Ind 64:708-719
26. Tsai DM, Rivera MDE (2019) Morphology-based defect detection in machined surfaces with circular tool-mark patterns. Meas J Int Meas Confed 134:209-217
27. Reed RC (2006) The superalloys fundamentals and applications. Cambridge University Press
28. Ramamurthy A, Sivaramakrishnan R, Muthuramalingam T et al (2015) Performance analysis of wire electrodes on machining Ti-6Al-4V alloy using electrical discharge machining process. Mach Sci Technol 19:577-592
29. Maher I, Sarhan AAD, Hamdi M (2014) Review of improvements in wire electrode properties for longer working time and utilization in wire EDM machining. Int J Adv Manuf Technol 76:329-351
30. Thakur DG, Ramamoorthy B, Vijayaraghavan L (2009) Study on the machinability characteristics of superalloy Inconel 718 during high speed turning. Mater Des 30:1718-1725
31. Abhilash PM, Chakradhar D (2021) Failure detection and control for wire EDM process using multiple sensors. CIRP J Manuf Sci Technol 33:315-326. https://doi.org/10.1016/j.cirpj.2021.04.009
32. Abhilash PM, Chakradhar D (2020) Surface integrity comparison of wire electric discharge machined Inconel 718 surfaces at different machining stabilities. Procedia CIRP 87:228-233
