Duplex stainless steels are being used on applications that require, especially, high corrosion resistance and overall good mechanical properties, such as the naval and oil-gas exploration industry. The components employed in these industries are usually obtained by machining, however, these alloys have low machinability when compared to conventional stainless steels. In this work, a study of the wear developed when milling duplex stainless-steel, LDX 2101, is going to be presented and evaluated, employing four types of milling tools with different geometries and coatings, while studying the influence of feed rate and cutting length in the wear of these tools. Tools used have been provided with two and four flutes, as well as three different coatings, namely: TiAlN, TiAlSiN and AlCrN. The cutting behavior of these tools was analyzed; data relative to the cutting forces developed during the process were obtained; and roughness measurements of the machined surfaces were executed. The tools were then submitted to scanning electron microscope (SEM) analysis, enabling the identification of the wear mechanisms that tools were subjected to when machining this material, furthermore, the early stages of these mechanisms were also identified. All this work was done with the goal of relating the machining parameters and cutting force values obtained, identifying, and discussing the wear patterns that were observed in the coating and tools after the milling tests, providing further information on the machining of these alloys.
The full text can be downloaded at https://link.springer.com/article/10.1007/s40436-022-00401-5
Vitor F. C. Sousa
,
Francisco J. G. Silva
,
Ricardo Alexandre
,
José S. Fecheira
,
Gustavo Pinto
,
Andresa Baptista
. Experimental study on the wear evolution of different PVD coated tools under milling operations of LDX2101 duplex stainless steel[J]. Advances in Manufacturing, 2023
, 11(1)
: 158
-179
.
DOI: 10.1007/s40436-022-00401-5
1. Cheng X, Wang Y, Li X et al (2018) Interaction between austein-ferrite phases on passive performance of 2205 duplex stainless steel. J Mater Sci Technol 34(11):2140-2148
2. Vinoth JA, Ajaykumar L, Deepak CR et al (2017) Weldability, machinability and surfacing of commercial duplex stainless steel AISI2205 for marine applications:a recent review. J Adv Res 8(3):183-199
3. Nomani J, Pramanik A, Hilditch T et al (2015) Chip formation mechanism and machinability of wrought duplex stainless steel alloys. Int J Adv Technol 80(5/8):1127-1135
4. Chail G, Kangas P (2016) Super and hyper duplex stainless steels:structures, properties, and applications. Procedia Struct Integrity 2:1755-1762
5. Nomani J, Pramanik A, Hilditch T et al (2013) Machinability study of first generation duplex (2205), second generation duplex (2507) and austenite stainless steel during drilling process. Wear 304(1/2):20-28
6. Koyee RD, Heisel U, Eisseler R et al (2014) Modeling and optimization of turning duplex stainless steels. J Manuf Processes 16(4):451-467
7. Gowthaman PS, Jeyakumar S, Saravanan BA (2020) Machinability and tool wear mechanism of duplex stainless steel:a review. Mater Today Proc 26(2):1423-1429
8. Sahithi VVD, Malayadrib T, Srilatha N (2019) Optimization of turning parameters on surface roughness based on Taguchi technique. Mater Today Proc 18:3657-3666
9. Tlhabadira I, Daniyan IA, Masu L et al (2019) Process design and optimization of surface roughness during M200 TS milling process using the Taguchi method. Procedia CIRP 84:868-873
10. Vishnu VM, Sankaraiah G, Yohan M et al (2017) Optimization of parameters in CNC milling of P20 steel using response surface methodology and Taguchi method. Mater Today Proc 4(8):9163-9169
11. Zhang JZ, Chen JC, Kirby ED (2007) Surface roughness optimization in an end-milling operation using the Taguchi design method. J Mater Process Technol 184(1/3):233-239
12. Kumar S, Saravanan I, Patnaik L (2020) Optimization of surface roughness and material removal rate in milling of AISI 1005 carbon steel using Taguchi approach. Mater Today Proc 22(3):654-658
13. Selvaraj DP (2017) Optimization of cutting force of duplex stainless steel in dry milling operation. Mater Today Proc 4(10):11141-11147
14. Airao J, Chaudhary B, Bajpai V (2018) Anexperimental study of surface roughness variation in end milling of super duplex 2507 stainless steel. Mater Today Proc 5(2):3682-3689
15. Policena MR, Devitte C, Fronza G et al (2018) Surface roughness analysis in finishing end-milling of duplex stainless steel UNS S32205. Inter J Adv Manuf Technol 98:1617-1625
16. Sousa VFC, Silva FJG (2020) Recent advances in turning processes using coated tools-a comprehensive review. Metals 10(2):170. https://doi.org/10.3390/met10020170
17. Sousa VFC, Silva FJG (2020) Recent advances on coated milling tool technology-a comprehensive review. Coatings 10(3):235. https://doi.org/10.3390/coatings10030235
18. Martinho RP, Silva FJG, Baptista APM (2008) Cutting forces and wear analysis of Si3N4 diamond coated tools in high speed machining. Vacuum 82(12):1415-1420
19. Paiva JMF, Amorim FL, Soares PC et al (2019) Tribological behavior of superduplex stainless steels against PVD hard coatings on cemented carbide. Inter J Adv Manuf Technol 90:1649-1658
20. Silva FJG, Martinho R, Andrade M et al (2017) Improving the wear resistance of moulds for the injection of glass fibre-reinforced plastics using PVD coatings:a comparative study. Coatings 7(2):28. https://doi.org/10.3390/coatings7020028
21. Silva FJG, Martinho RP, Alexandre RJD et al (2011) Increasing the wear resistance of molds for injection of glass fiber reinforced plastics. Wear 271(9/10):2494-2499
22. Silva FJG, Martinho RP, Baptista APM (2014) Characterization of laboratory and industrial CrN/CrCn/diamond-like carbon coatings. Thin Solid Films 550(1):278-284
23. Silva FJG, Fernandes AJS, Costa FM (2003) Tribological behaviour of CVD diamond films on steel substrates. Wear 255:846-853
24. Silva FJG, Fernandes AJS, Costa FM et al (2005) Unstressed PACVD diamond films on steel pre-coated with a composite multilayer. Surf Coat Technol 191:102-107
25. Baptista A, Silva FJG, Porteiro J et al (2018) Sputtering physical vapour deposition (PVD) coatings:a critical review on process improvement and market trend demands. Coatings 8:402. https://doi.org/10.3390/coatings8110402
26. Baptista A, Silva FJG, Porteiro J et al (2018) On the physical vapour deposition (PVD):evolution of magnetron sputtering processes for industrial applications. Procedia Manuf 17:746-757
27. Martinho RP, Silva FJG, Martins C et al (2019) Comparative study of PVD and CVD cutting tools performance in milling of duplex stainless steel. Int J Adv Manuf Technol 102:2423-2439
28. Ginting A, Skein R, Cuaca D et al (2018) The characteristics of CVD- and PVD-coated carbide tools in hard turning of AISI 4340. Measurement 129:548-557
29. Koseki S, Inoue K, Morito S et al (2015) Comparison of TiN-coated tools using CVD and PVD processes during continuous cutting of Ni-based superalloys. Surf Coat Technol 283:353-363
30. Caliskan H, Panjan P, Kurbanoglu C (2017) 3.16 Hard coatings on cutting tools and surface finish. Compr Mater Finish 3:230-242
31. Paiva JMF, Torres RD, Amorim FL et al (2017) Frictional and wear performance of hard coatings during machining of super duplex stainless steel. Int J Adv Manuf Technol 92:423-432
32. Klocke F, Krieg T (1999) Coated tools for metal cutting-features and applications. CIRP Ann 48:515-525
33. Fernández-Abia AI, Barreiro J, Fernández-Larrinoa J et al (2013) Behaviour of PVD coatings in the turning of austenitic stainless steels. Procedia Eng 63:133-141
34. Vasu M, Nayaka HS (2018) Investigation of cutting force tool tip temperature and surface roughness during dry machining of spring steel. Mater Today Proc 5(2):7141-7149
35. Phokobye SN, Daniyan IA, Tlhabadira I et al (2019) Model design and optimization of carbide milling cutter for milling operation of M200 tool steel. Procedia CIRP 84:954-959
36. Strafford KN, Audy J (1997) Indirect monitoring of machinability in carbon steels by measurement of cutting forces. J Mater Process Tech 67(1/3):150-156
37. Venkatesan K, Manivannan K, Devendiran S et al (2019) Study of forces, surface finish and chip morphology on machining of Inconel 825. Procedia Manuf 30:611-618
38. Caudill J, Schoop J, Jawahir IS (2019) Numerical modeling of cutting forces and temperature distribution in high speed cryogenic and flood-cooled milling of Ti-6Al-4V. Procedia CIRP 82:83-88
39. Fernández-Abia AI, Barreiro J, López de Lacalle LN (2012) Behavior of austenitic stainless steels at high speed turning using specific force coefficients. Int J Adv Manuf Technol 62:505-515
40. Batuev VA, Batuev VV, Ardashev DV et al (2019) Analytical calculation of cutting forces and analysis of their change at 3-D milling. Procedia Manuf 32:42-49
41. Davoudinejad A, Chiappini E, Tirelli S et al (2015) Finite element simulation and validation of chip formation and cutting forces in dry and cryogenic cutting of Ti-6Al-4V. Procedia Manuf 1:728-739
42. Bhopale S, Jagatap KR, Lamdhade GK et al (2017) Cutting forces during orthogonal machining process of AISI 1018 steel:numerical and experimental modeling. Mater Today Proc 4(8):8454-8462
43. Mebrahitom A, Choon W, Azhari A (2017) Side milling machining simulation using finite element analysis:prediction of cutting forces. Mater Today Proc 4(4):5215-8521
44. Gouveia R, Silva FJG, Reis P et al (2016) Machining duplex stainless steel:comparative study regarding end mill coated tools. Coatings 6(4):51. https://doi.org/10.3351/coatings6040051
45. Seid Ahmed Y, Paiva J, Covelli D et al (2017) Investigation of coated cutting tool performance during machining of super duplex stainless steels through 3D wear evaluations. Coatings 7(8):127. https://doi.org/10.3390/coatings7080127
46. Dos Santos AG, da Silva MB, Jackson MJ (2018) Tungsten carbide micro-tool wear when micro milling UNS S32205 duplex stainless steel. Wear 414/415(15):109-117
47. Diniz AE, Machado AR, Corrêa JG (2016) Tool wear mechanisms in the machining of steels and stainless steels. Int J Adv Manuf Technol 8:3157-3168
48. Silva F, Martinho R, Martins C et al (2019) Machining GX2CrNiMoN26-7-4 DSS alloy:wear analysis of TiAlN and TiCN/Al2O3/TiN coated carbide tools behavior in rough end milling operations. Coatings 9(6):392. https://doi.org/10.3390/coatings9060392
49. Krolczyk GM, Nieslony P, Legutko S (2015) Determination of tool life and research wear during duplex stainless steel turning. Arch Civ Mech Eng 15(2):347-354
50. Rajaguru J, Arunachalam N (2017) Coated tool performance in dry turning of super duplex stainless steel. Procedia Manuf 10:601-611
51. Suárez A, López de Lacalle LN, Polvorosa R et al (2017) Effects of high-pressure cooling on the wear patterns on turning inserts used on alloy IN718. Mater Manuf Process 32(6):678-686
52. ISO 8688-2:1986 (1986) Tool life testing in milling-part 2:end milling, International Organization for Standardization, Geneva
53. Sousa VFC, Silva FJG, Alexandre R et al (2021) Study of the wear behaviour of TiAlSiN and TiAlN PVD coated tools on milling operations of pre-hardened tool steel. Wear 476:203695. https://doi.org/10.1016/j.wear.2021.203695
