Experimental study and optimization of cutting parameters in machining of super alloy with hybrid ultrasonic method

doi:10.1007/s40436-017-0185-6

摘要/Abstract

摘要：

Super alloys are intensively used in various industries, especially in the aerospace industry, because of their special characteristics. A number of holes are sometimes required to be drilled into super alloys for aircraft at their final stage assembly. In the present study, a hybrid ultrasonic machining method, called rotary ultrasonic machining (RUM), was successfully used in super alloy drilling. The empirical modeling of the process parameters of RUM was performed for the super alloy (Inconel 718) using an experimental design approach, called response surface methodology (RSM). Parameters, namely tool rotation, feed rate, ultrasonic power, and abrasive grit size, were selected as input variables. The others were kept constant. The performance was measured in terms of the machining rate and the surface roughness. The developed models were found to be reliable representatives of the experimental results with prediction errors less than ±5%. Moreover, the feed rate for the quality and productivity aspect was found to be the most critical factor. The optimized values of the machining rate and the surface roughness achieved through a multi-response optimization were 0.9 825 mm³/s and 0.951 μm, respectively.

The full text can be downloaded at https://link.springer.com/article/10.1007/s40436-017-0185-6

关键词: Super alloy, Rotary ultrasonic machining (RUM), Ultrasonic, Roughness, Machining

Abstract:

Key words: Super alloy, Rotary ultrasonic machining (RUM), Ultrasonic, Roughness, Machining

Dipesh Popli, Meenu Gupta. Experimental study and optimization of cutting parameters in machining of super alloy with hybrid ultrasonic method[J]. Advances in Manufacturing, 2017, 5(3): 199-216.

参考文献

1. Davis JR, Associates (2000) ASM specialty handbook: nickel, cobalt, and their alloys. ASM International Handbook Committee
2. Nalbant M, Alt?n A, Gokkaya H (2007) The effect of cutting speed and cutting tool geometry on machinability properties of nickel-base Inconel 718 super alloys. Mater Des 28:1334- 1338
3. Khidhir BA, Mohamed B (2010) Machining of nickel based alloys using different cemented carbide tools. J Eng Sci Technol 5:264-271
4. Dreshfiezd RL (1970) Estimation of gamma phase composition in nickel-base superalloys (based on geometric analysis of a fourcomponent phase diagram). Nasa technical note
5. Zhou J, Bushlya V, Avdovic P et al (2012) Study of surface quality in high speed turning of Inconel 718 with uncoated and coated CBN tools. Int J Adv Manuf Technol 58:141-151
6. Bhatt A, Attia H, Vargas R et al (2010) Wear mechanisms of WC coated and uncoated tools in finish turning of Inconel 718. Tribol Int 43:1113-1121
7. Pei ZJ, Ferreira PM, Kapoor SG et al (1995) Rotary ultrasonic machining for face milling of ceramics. Int J Mach Tools Manuf 35:1033-1046
8. Zhang CL, Feng PF, Wu ZJ et al (2011) An experimental study on processing performance of rotary ultrasonic drilling of K9 glass. Adv Mater Res 230-232:221-225
9. Hu P, Zhang J, Pei ZJ et al (2002) Modeling of material removal rate in rotary ultrasonic machining: designed experiments. J Mater Process Technol 129:339-344
10. Lauwers B, Bleicher F, Haaf P (2010) Investigation of the process-material interaction in ultrasonic assisted grinding of ZrO₂ based ceramic materials. In: proceedings of 4th CIRP international conference on high performance cutting, 24-26 October 2010, pp 59-64
11. Li ZC, Jiao Y, Deines TW et al (2005) Rotary ultrasonic machining of ceramic matrix composites: feasibility study and designed experiments. Int J Mach Tools Manuf 45:1402-1411
12. Kataria R, Kumar J, Pabla BS (2015) Experimental investigation into the hole quality in ultrasonic machining of WC-Co composite. Mater Manuf Process 30:921-933
13. Singh RP, Singhal S (2016) Investigation of machining characteristics in rotary ultrasonic machining of alumina ceramic. Mater Manuf Process 6914(10426914):1176190
14. Singh RP, Singhal S (2016) Experimental investigation of machining characteristics in rotary ultrasonic machining of quartz ceramic. J Mater Des Appl 0:1-20
15. Singh RP, Singhal S (2016) Experimental study on rotary ultrasonic machining of alumina ceramic: microstructure analysis and multi-response optimization. Proc Inst Mech Eng Part L J Mater Des Appl 0:1-20
16. Churi NJ, Pei ZJ, Treadwell C (2006) Rotary ultrasonic machining of titanium alloy: effects of machining variables. Mach Sci Technol 10:301-321
17. Zou XT (2013) Cutting temperature in rotary ultrasonic machining of titanium: experimental study using novel FabryPerot fibre optic sensors. Int J Manuf Res 8:250-261
18. Lv D, Tang Y, Wang H et al (2013) Experimental investigations on subsurface damage in rotary ultrasonic machining of glass BK7. Mach Sci Technol 17:443-463
19. Feng Q, Cong WL, Pei ZJ et al (2012) Rotary ultrasonic machining of carbon fiber-reinforced polymer: feasibility study. Mach Sci Technol 16:380-398
20. Jiao Y, Liu WJ, Pei ZJ et al (2005) Study on edge chipping in rotary ultrasonic machining of ceramics: an integration of designed experiments and finite element method analysis. J Manuf Sci Eng 127:752-758
21. Zhang CL, Feng PF, Pei ZJ et al (2013) Rotary ultrasonic machining of sapphire: feasibility study and designed experiments. Key Eng Mater 589-590:523-528
22. Churi NJ, Pei ZJ, Shorter DC et al (2007) Rotary ultrasonic machining of silicon carbide: designed experiments. Int J Manuf Technol Manag 12:284-298
23. Debnath K, Singh I (2017) Low-frequency modulation-assisted drilling of carbon-epoxy composite laminates. J Manuf Process 25:262-273
24. Okamura K, Sasahara H, Segawa T et al (2006) Low-frequency vibration drilling of titanium alloy. JSME Int J Ser C 49:76-82
25. Torres A, Luis CJ, Puertas I (2015) Analysis of the influence of EDM parameters on surface finish, material removal rate, and electrode wear of an Inconel 600 alloy. Int J Adv Manuf Technol 80:123-140
26. Montgomery DC (2008) Design and analysis of experiments. Wiley, New York
27. Pi J, Yang G, Ye F (2013) Study on impact stress characteristics in ultrasonic cutting and brittle material removal mechanism. Adv Mater Res 753-755:287-297
28. Derringer G, Suich R (1980) Simultaneous optimization of several response variables. J Qual Technol 12(4):214-219

[1]	Wei Zhao, Asif Iqbal, Ding Fang, Ning He, Qi Yang. Experimental study on the meso-scale milling of tungsten carbide WC-17.5Co with PCD end mills[J]. Advances in Manufacturing, 2020, 8(2): 230-241.
[2]	Xiao-Fen Liu, Wen-Hu Wang, Rui-Song Jiang, Yi-Feng Xiong, Kun-Yang Lin. Tool wear mechanisms in axial ultrasonic vibration assisted milling in-situ TiB₂/7050Al metal matrix composites[J]. Advances in Manufacturing, 2020, 8(2): 252-264.
[3]	Xiang Zou, Hon-Yuen Tam, Hai-Yin Xu, Ke Shi. Flat-end tool orientation based on rotation-minimizing frame[J]. Advances in Manufacturing, 2019, 7(3): 257-269.
[4]	Jun-Yun Chen, Tian-Ye Jin, Xi-Chun Luo. Key machining characteristics in ultrasonic vibration cutting of single crystal silicon for micro grooves[J]. Advances in Manufacturing, 2019, 7(3): 303-314.
[5]	Tian-Xun Xiu, Wei Wang, Kun Liu, Zhi-Yong Wang, Dao-Zhu Wei. Characteristics of force chains in frictional interface during abrasive flow machining based on discrete element method[J]. Advances in Manufacturing, 2018, 6(4): 355-375.
[6]	Saroj Kumar Padhi, S. S. Mahapatra, Rosalin Padhi, Harish Chandra Das. Performance analysis of a thick copper-electroplated FDM ABS plastic rapid tool EDM electrode[J]. Advances in Manufacturing, 2018, 6(4): 442-456.
[7]	Mukesh Kumar Sindhu, Debasish Nandi, Indrajit Basak. Electric discharge phenomenon in dielectric and electrolyte medium[J]. Advances in Manufacturing, 2018, 6(4): 457-464.
[8]	Lutfi Taner Tunc, Orkun Ozsahin. Use of inverse stability solutions for identification of uncertainties in the dynamics of machining processes[J]. Advances in Manufacturing, 2018, 6(3): 308-318.
[9]	Ehsan Jafarzadeh, Mohammad R. Movahhedy, Saeed Khodaygan, Mohammad Ghorbani. Prediction of machining chatter in milling based on dynamic FEM simulations of chip formation[J]. Advances in Manufacturing, 2018, 6(3): 334-344.
[10]	V. G. Ladeesh, R. Manu. Effect of machining parameters on edge-chipping during drilling of glass using grinding-aided electrochemical discharge machining (G-ECDM)[J]. Advances in Manufacturing, 2018, 6(2): 215-224.
[11]	Somvir Singh Nain, Dixit Garg, Sanjeev Kumar. Evaluation and analysis of cutting speed, wire wear ratio, and dimensional deviation of wire electric discharge machining of super alloy Udimet-L605 using support vector machine and grey relational analysis[J]. Advances in Manufacturing, 2018, 6(2): 225-246.
[12]	Ramanuj Kumar, Ashok Kumar Sahoo, Purna Chandra Mishra, Rabin Kumar Das. Comparative investigation towards machinability improvement in hard turning using coated and uncoated carbide inserts: part I experimental investigation[J]. Advances in Manufacturing, 2018, 6(1): 52-70.
[13]	Sandip Kunar, B. Bhattacharyya. Investigation on surface structuring generated by electrochemical micromachining[J]. Advances in Manufacturing, 2017, 5(3): 217-230.
[14]	Szymon Wojciechowski, Zbigniew Nowakowski, Radomir Majchrowski, Grzegorz Królczyk. Surface texture formation in precision machining of direct laser deposited tungsten carbide[J]. Advances in Manufacturing, 2017, 5(3): 251-260.
[15]	Ravindra Nath Yadav. Development and experimental investigation of duplex turning process[J]. Advances in Manufacturing, 2017, 5(2): 149-157.