Electrical arc contour cutting based on a compound arc breaking mechanism

doi:10.1007/s40436-022-00406-0

Advances in Manufacturing ›› 2022, Vol. 10 ›› Issue (4): 583-595.doi: 10.1007/s40436-022-00406-0

• ARTICLES • 上一篇

Electrical arc contour cutting based on a compound arc breaking mechanism

Guo-Jian He¹, Lin Gu¹, Ying-Mou Zhu¹, Ji-Peng Chen², Wan-Sheng Zhao¹, K. P. Rajurkar³

1. State Key Laboratory of Mechanical System and Vibration, School of Mechanical Engineering, Shanghai Jiao Tong University, Shanghai, 200240, People's Republic of China;
2. School of Mechanical and Electronic Engineering, Nanjing Forestry University, Nanjing, 210037, People's Republic of China;
3. Center for Nontraditional Manufacturing Research, University of Nebraska-Lincoln, Lincoln, NE, USA

收稿日期:2021-06-26 修回日期:2021-10-22 发布日期:2022-11-05
通讯作者: Lin Gu E-mail:lgu@sjtu.edu.cn
基金资助:
The authors acknowledge the National Science Foundation of China (Grants Nos. 51235007 and 51575351) and the State Key Laboratory of Mechanical System and Vibration of China (Grant No. MSV201305) for their fnancial support of this research.

Electrical arc contour cutting based on a compound arc breaking mechanism

Guo-Jian He¹, Lin Gu¹, Ying-Mou Zhu¹, Ji-Peng Chen², Wan-Sheng Zhao¹, K. P. Rajurkar³

1. State Key Laboratory of Mechanical System and Vibration, School of Mechanical Engineering, Shanghai Jiao Tong University, Shanghai, 200240, People's Republic of China;
2. School of Mechanical and Electronic Engineering, Nanjing Forestry University, Nanjing, 210037, People's Republic of China;
3. Center for Nontraditional Manufacturing Research, University of Nebraska-Lincoln, Lincoln, NE, USA

Received:2021-06-26 Revised:2021-10-22 Published:2022-11-05
Contact: Lin Gu E-mail:lgu@sjtu.edu.cn
Supported by:
The authors acknowledge the National Science Foundation of China (Grants Nos. 51235007 and 51575351) and the State Key Laboratory of Mechanical System and Vibration of China (Grant No. MSV201305) for their fnancial support of this research.

摘要/Abstract

摘要： Electrical arc contour cutting (EACC) is a novel high-efficiency material cutting process that applies arc plasma to perform efficient and economical contour cutting of difficult-to-cut materials. Compared to conventional electrical arc machining (EAM), this process can remove the allowance of open structures and plates in bulk mode, rather than entirely in the form of debris. Compared with existing contour cutting methods, EACC possesses the advantages of high cutting efficiency and a deep cutting depth. Particularly, a compound arc breaking mechanism (CABM), which integrates hydrodynamic force and mechanical motion, has been applied to control the discharge arc column in EACC, while also strengthening the debris expelling effect in the narrow discharge gap. The CABM implementation conditions were studied, based on arc column distortion images captured by a high-speed camera and simulation results of the flow field and debris distribution. A set of machining experiments was designed and conducted to optimize the performance of the proposed process. Finally, a SiC_p/Al metal matrix composite (MMC) space station workpiece was machined to verify the feasibility and efficiency of this process.

The full text can be downloaded at https://link.springer.com/article/10.1007/s40436-022-00406-0

关键词: Electrical arc contour cutting (EACC), Electrical arc machining (EAM), Compound arc breaking mechanism (CABM), SiC_p/Al metal matrix composite (MMC), High efficiency

Abstract: Electrical arc contour cutting (EACC) is a novel high-efficiency material cutting process that applies arc plasma to perform efficient and economical contour cutting of difficult-to-cut materials. Compared to conventional electrical arc machining (EAM), this process can remove the allowance of open structures and plates in bulk mode, rather than entirely in the form of debris. Compared with existing contour cutting methods, EACC possesses the advantages of high cutting efficiency and a deep cutting depth. Particularly, a compound arc breaking mechanism (CABM), which integrates hydrodynamic force and mechanical motion, has been applied to control the discharge arc column in EACC, while also strengthening the debris expelling effect in the narrow discharge gap. The CABM implementation conditions were studied, based on arc column distortion images captured by a high-speed camera and simulation results of the flow field and debris distribution. A set of machining experiments was designed and conducted to optimize the performance of the proposed process. Finally, a SiC_p/Al metal matrix composite (MMC) space station workpiece was machined to verify the feasibility and efficiency of this process.

The full text can be downloaded at https://link.springer.com/article/10.1007/s40436-022-00406-0

Key words: Electrical arc contour cutting (EACC), Electrical arc machining (EAM), Compound arc breaking mechanism (CABM), SiC_p/Al metal matrix composite (MMC), High efficiency

Guo-Jian He, Lin Gu, Ying-Mou Zhu, Ji-Peng Chen, Wan-Sheng Zhao, K. P. Rajurkar. Electrical arc contour cutting based on a compound arc breaking mechanism[J]. Advances in Manufacturing, 2022, 10(4): 583-595.

参考文献

1. Klocke F, Schmitt R, Zeis M (2015) Technological and economical assessment of alternative process chains for blisk manufacture. Proc CIRP 35: 67–72
2. Bergs T, Grünebaum T, Fricke K et al (2021) Life cycle assessment for milling of Ti- and Ni-based alloy aero engine components. Proc CIRP 98: 625–630
3. Klocke F, Klink A, Veselovac D et al (2014) Turbomachinery component manufacture by application of electrochemical, electro-physical and photonic processes. CIRP Ann Manuf Technol 63(2): 703–726
4. Ma B, Zhu Y, Jin X (2011) Wire electro discharge machining of Al/SiC metal matrix composite. Appl Mech Mater 121/126: 564–567
5. Krajcarz D (2014) Comparison metal water jet cutting with laser and plasma cutting. Proc Eng 69: 838–843
6. Zhao W, Gu L, Xu H et al (2013) A novel high efficiency electrical erosion process-blasting erosion arc machining. Proc CIRP 6: 622–626
7. Wang F, Liu Y, Tang Z et al (2014) Ultra-high-speed combined machining of electrical discharge machining and arc machining. Proc Inst Mech Eng B J Eng Manuf 228(5): 663–672
8. Wang F, Liu Y, Shen Y et al (2013) Machining performance of Inconel 718 using high current density electrical discharge milling. Mater Manuf Process 28: 1147–1152
9. Gu L, Chen J, Xu H et al (2016) Blasting erosion arc machining of 20 vol. % SiC/Al metal matrix composites. Int J Adv Manuf Technol 87(9): 2775–2784
10. Shen Y, Liu Y, Sun W et al (2015) High-speed dry compound machining of Ti6Al4V. J Mater Process Technol 224: 200–207
11. Zhang R, Zhang Y, Liu Y et al (2017) Energy distribution and material removal of electric arc machining (EAM). J Mater Process Technol 242: 110–116
12. Meshcheriakov G, Nosulenko V, Meshcheriakov N et al (1988) Physical and technological control of arc dimensional machining. CIRP Ann Manuf Technol 37: 209–212
13. Kou Z, Han F (2018) Machining characteristics and removal mechanisms of moving electric arcs in high-speed EDM milling. J Manuf Process 189: 78–87
14. Gu L, Zhang F, Zhao W et al (2016) Investigation of hydrodynamic arc breaking mechanism in blasting erosion arc machining. CIRP Ann Manuf Technol 65(1): 233–236
15. Zhang F, Gu L, Chen J et al (2016) Observation and modeling research of high-velocity flushing effect on the performance of BEAM. Int J Adv Manuf Technol 86(1): 935–942
16. Wang C, Cheng J, Gu L et al (2016) Blasting erosion arc machining of turbine blisk flow channel with laminated electrode. Proc CIRP 42: 317–321
17. Chen J, Gu L, Xu H et al (2016) Study on blasting erosion arc machining of Ti-6Al-4V alloy. Int J Adv Manuf Technol 85: 9–12
18. Liu H, Zhou J, Yu Q (2014) Analysis of mechanical quality of Nickel-base superalloy machined by short electric arc. Asian J Chem 26(17): 5469–5472
19. Farhadi A, Gu L, Zhao W et al (2020) Tool path optimization based on wear prediction in electric arc sweep machining. J Manuf Process 54: 328–336
20. Zhu Y, Chen J, Xu H et al (2016) Research on the surface quality of the blasting erosion arc machined stainless steel. Proc CIRP 42: 252–256
21. Chen J, Gu L, Liu X et al (2018) Combined machining of SiC/Al composites based on blasting erosion arc machining and CNC milling. Int J Adv Manuf Technol 96: 111–121

Electrical arc contour cutting based on a compound arc breaking mechanism

Electrical arc contour cutting based on a compound arc breaking mechanism

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 0

编辑推荐

Metrics

本文评价