State of the art of bioimplants manufacturing: part I

doi:10.1007/s40436-017-0207-4

Advances in Manufacturing ›› 2018, Vol. 6 ›› Issue (1): 20-40.doi: 10.1007/s40436-017-0207-4

State of the art of bioimplants manufacturing: part I

Cheng-Wei Kang¹, Feng-Zhou Fang^1,2

1 Centre of MicroNano Manufacturing Technology(MNMTDublin), University College Dublin, Dublin, Ireland;
2 State Key Laboratory of Precision Measuring Technology and Instruments, Centre of MicroNano Manufacturing Technology, Tianjin University, Tianjin 300072, People's Republic of China

收稿日期:2017-11-14 修回日期:2017-12-20 出版日期:2018-03-25 发布日期:2018-03-25
通讯作者: Feng-Zhou Fang,fengzhou.fang@ucd.ie E-mail:fengzhou.fang@ucd.ie
基金资助:
Acknowledgements are extended to the support received from the Science Foundation Ireland (SFI) (Grant No. 15/RP/B3208) and the National Science Foundation of China (Grant Nos. 51320105009 & 61635008).

State of the art of bioimplants manufacturing: part I

Cheng-Wei Kang¹, Feng-Zhou Fang^1,2

1 Centre of MicroNano Manufacturing Technology(MNMTDublin), University College Dublin, Dublin, Ireland;
2 State Key Laboratory of Precision Measuring Technology and Instruments, Centre of MicroNano Manufacturing Technology, Tianjin University, Tianjin 300072, People's Republic of China

Received:2017-11-14 Revised:2017-12-20 Online:2018-03-25 Published:2018-03-25
Contact: Feng-Zhou Fang,fengzhou.fang@ucd.ie E-mail:fengzhou.fang@ucd.ie
Supported by:
Acknowledgements are extended to the support received from the Science Foundation Ireland (SFI) (Grant No. 15/RP/B3208) and the National Science Foundation of China (Grant Nos. 51320105009 & 61635008).

摘要/Abstract

摘要：

Bioimplants are becoming increasingly important in the modern society due to the fact of an aging population and associated issues of osteoporosis and osteoarthritis. The manufacturing of bioimplants involves an understanding of both mechanical engineering and biomedical science to produce biocompatible products with adequate lifespans. A suitable selection of materials is the prerequisite for a long-term and reliable service of the bioimplants, which relies highly on the comprehensive understanding of the material properties. In this paper, most biomaterials used for bioimplants are reviewed. The typical manufacturing processes are discussed in order to provide a perspective on the development of manufacturing fundamentals and latest technologies. The review also contains a discussion on the current measurement and evaluation constraints of the finished bioimplant products. Potential future research areas are presented at the end of this paper.

The full text can be downloaded at https://link.springer.com/article/10.1007/s40436-017-0207-4

关键词: Bioimplant, Precision manufacturing, Precision metrology, Evaluation

Abstract:

Key words: Bioimplant, Precision manufacturing, Precision metrology, Evaluation

Cheng-Wei Kang, Feng-Zhou Fang. State of the art of bioimplants manufacturing: part I[J]. Advances in Manufacturing, 2018, 6(1): 20-40.

参考文献

1. Manivasagam G, Dhinasekaran D, Rajamanickam A (2010) Biomedical implants:corrosion and its prevention-a review. Recent Pat Corros Sci 2(1):40-54
2. Luthringer B, Feyerabend F, Willumeit-Römer R (2014) Magnesium-based implants:a mini-review. Magnes Res 27(4):142-154
3. Geetha M, Singh A, Asokamani R et al (2009) Ti based biomaterials, the ultimate choice for orthopaedic implants-a review. Prog Mater Sci 54(3):397-425
4. Walczak J, Shahgaldi F, Heatley F (1998) In vivo corrosion of 316L stainless-steel hip implants:morphology and elemental compositions of corrosion products. Biomaterials 19(1-3):229-237
5. Case C, Langkamer V, James C et al (1994) Widespread dissemination of metal debris from implants. Bone Joint J 76(5):701-712
6. Prikryl M, Srivastava S, Viviani G et al (1989) Role of corrosion in harrington and luque rods failure. Biomaterials 10(2):109-117
7. Sumita M, Hanawa T, Ohnishi I et al (2003) Failure processes in biometallic materials. In:Milne I, Ritchie R, Karihaloo BL (eds) IMOR Karihaloo, comprehensive structural integrity, Pergamon, Oxford, pp 131-167
8. Davis JR (2003) Handbook of materials for medical devices. ASM International, Metals Park
9. Shetty RH, Ottersberg WH (1995) Metals in orthopedic surgery. Encycl Handb Biomater Bioeng 1:509-540
10. Lemons J, Niemann K, Weiss A (1976) Biocompatibility studies on surgical-grade titanium-, cobalt-, and iron-base alloys. J Biomed Mater Res, Part A 10(4):549-553
11. Escalas F, Galante J, Rostoker W et al (1976) Biocompatibility of materials for total joint replacement. J Biomed Mater Res, Part A 10(2):175-195
12. Syrett BC, Davis EE (1979) In vivo evaluation of a highstrength, high-ductility stainless steel for use in surgical implants. J Biomed Mater Res, Part A 13(4):543-556
13. Breme H, Biehl V, Helsen J (1998) Metals and implants. Metals Biomater 615(46):37-72
14. David Y (1999) The biomedical engineering handbook. In:Bronzino JD (ed) The biomedical engineering handbook, 2nd edn. 2 Volume Set. CRC Press, Boca Raton
15. Wiles P (1958) The surgery of the osteo-arthritic hip. Br J Surg 45(193):488-497
16. Wiles P (2003) The classic:the surgery of the osteo-arthritic hip. Clin Orthop Relat Res 417:3-16
17. Niinomi M, Nakai M, Hieda J (2012) Development of new metallic alloys for biomedical applications. Acta Biomater 8(11):3888-3903
18. Chen Q, Thouas GA (2015) Metallic implant biomaterials. Mater Sci Eng R Rep 87:1-57
19. Taira M, Lautenschlager EP (1992) In vitro corrosion fatigue of 316L cold worked stainless steel. J Biomed Mater Res 26(9):1131-1139
20. Weldon L, McHugh P, Carroll W et al (2005) The influence of passivation and electropolishing on the performance of medical grade stainless steels in static and fatigue loading. J Mater Sci Mater Med 16(2):107-117
21. Roland T, Retraint D, Lu K et al (2006) Fatigue life improvement through surface nanostructuring of stainless steel by means of surface mechanical attrition treatment. Scr Mater 54(11):1949-1954
22. Sudarshan T, Srivatsan T, Harvey D (1990) Fatigue processes in metals-role of aqueous environments. Eng Fract Mech 36(6):827-852
23. Ebara R (2010) Corrosion fatigue crack initiation behavior of stainless steels. Procedia Eng 2(1):1297-1306
24. Vahey J, Simonian P, Conrad E (1995) Carcinogenicity and metallic implants. Am J Orthoped (Belle Mead, NJ) 24(4):319-324
25. Lei M, Zhu X (2001) In vitro corrosion resistance of plasma source ion nitrided austenitic stainless steels. Biomaterials 22(7):641-647
26. Nail-plates F (1959) Corrosion of orthopaedic implants. J Bone Jt Surg B 41:810-820
27. Muley SV, Vidvans AN, Chaudhari GP et al (2016) An assessment of ultra fine grained 316L stainless steel for implant applications. Acta Biomater 30:408-419
28. Pramanik S, Agarwal AK, Rai K (2005) Chronology of total hip joint replacement and materials development. Trends Biomater Artif Organs 19(1):15-26
29. Patel NR, Gohil PP (2012) A review on biomaterials:scope, applications & human anatomy significance. Int J Emerg Technol Adv Eng 2(4):91-101
30. Alvarado J, Maldonado R, Marxuach J et al (2003) Biomechanics of hip and knee prostheses. Appl Eng Mech Med GED-University of Puerto Rico Mayaguez
31. Evans E, Thomas I (1986) The in vitro toxicity of cobaltchrome-molybdenum alloy and its constituent metals. Biomaterials 7(1):25-29
32. Öztürk O, Türkan Uu, Eroglu AE (2006) Metal ion release from nitrogen ion implanted CoCrMo orthopedic implant material. Surf Coat Technol 200(20):5687-5697
33. Vidal CV, Muñoz AI (2009) Effect of thermal treatment and applied potential on the electrochemical behaviour of CoCrMo biomedical alloy. Electrochim Acta 54(6):1798-1809
34. Ramsden JJ, Allen DM, Stephenson DJ et al (2007) The design and manufacture of biomedical surfaces. CIRP Ann Manuf Technol 56(2):687-711
35. Rudolf E (1998) A review of findings on chromium toxicity. Acta Med (Hradec Kralove) Suppl 41(1):55-65
36. Dayan A, Paine A (2001) Mechanisms of chromium toxicity, carcinogenicity and allergenicity:review of the literature from 1985 to 2000. Hum Exp Toxicol 20(9):439-451
37. Barceloux DG, Barceloux D (1999) Chromium. J Toxicol Clin Toxicol 37(2):173-194
38. Barceloux DG, Barceloux D (1999) Nickel. J Toxicol Clin Toxicol 37(2):239-258
39. Anke M, Seifert M, Arnhold W et al (2010) The biological and toxicological importance of molybdenum in the environment and in the nutrition of plants, animals and man:part V:essentiality and toxicity of molybdenum. Acta Aliment 39(1):12-26
40. Nagels J, Stokdijk M, Rozing PM (2003) Stress shielding and bone resorption in shoulder arthroplasty. J Shoulder Elbow Surg 12(1):35-39
41. Park JB, Lakes RS (2007) Hard tissue replacement Ⅱ:joints and teeth. In:Hasirci N, Hasirci V (eds) Biomaterials. Springer, Boston, pp 317-354
42. Long M, Rack H (1998) Titanium alloys in total joint replacement-a materials science perspective. Biomaterials 19(18):1621-1639
43. Pais I, Feher M, Farkas E et al (1977) Titanium as a new trace element. Commun Soil Sci Plant Anal 8(5):407-410
44. Okazaki Y (2002) Effect of friction on anodic polarization properties of metallic biomaterials. Biomaterials 23(9):2071-2077
45. Yaghoubi S, Schwietert CW, McCue JP (2000) Biological roles of titanium. Biol Trace Elem Res 78(1-3):205
46. Niinomi M (2008) Biologically and mechanically biocompatible titanium alloys. Mater Trans 49(10):2170-2178
47. Niinomi M (2002) Recent metallic materials for biomedical applications. Metall Mater Trans A 33(3):477-486
48. Niinomi M (2003) Recent research and development in titanium alloys for biomedical applications and healthcare goods. Sci Technol Adv Mater 4(5):445-454
49. Niinomi M (1999) Recent titanium R&D for biomedical applications in Japan. JOM 51(6):32-34
50. Charnley J (1970) Total hip replacement by low-friction arthroplasty. Clin Orthop Relat Res 72:7-21
51. Ramakrishna S, Mayer J, Wintermantel E et al (2001) Biomedical applications of polymer-composite materials:a review. Compos Sci Technol 61(9):1189-1224
52. Kurella A, Dahotre NB (2005) Review paper:surface modification for bioimplants:the role of laser surface engineering. J Biomater Appl 20(1):5-50
53. Hench LL, Wilson J (1993) An introduction to bioceramics, vol1. World Scientific, Singapore
54. Katti KS (2004) Biomaterials in total joint replacement. Colloids Surf B 39(3):133-142
55. Kamitakahara M, Ohtsuki C, Miyazaki T (2008) Review paper:behavior of ceramic biomaterials derived from tricalcium phosphate in physiological condition. J Biomater Appl 23(3):197-212
56. Park JB, Bronzino JD (2002) Biomaterials:principles and applications. CRC Press, Boca Raton
57. De Aza P, De Aza A, Pena P et al (2007) Bioactive glasses and glass-ceramics. Bol Soc Esp Ceram Yvid 46(2):45
58. Hench LL (1991) Bioceramics:from concept to clinic. J Am Ceram Soc 74(7):1487-1510
59. Daculsi G (1998) Biphasic calcium phosphate concept applied to artificial bone, implant coating and injectable bone substitute. Biomaterials 19(16):1473-1478
60. Fujita Y, Yamamuro T, Nakamura T et al (1991) The bonding behavior of calcite to bone. J Biomed Mater Res, Part A 25(8):991-1003
61. Piconi C, Maccauro G (1999) Zirconia as a ceramic biomaterial. Biomaterials 20(1):1-25
62. Ikada Y (2002) Recent research developments in biomaterials. Research Signpost, India
63. Boutin P (1971) Alumina and its use in surgery of the hip. (Experimental study). La Presse Medicale 79(14):639-640
64. Kokubo T (2008) Bioceramics and their clinical applications. Laryngoscope 92(1):1103-1115
65. Heros RJ, Willmann G (1998) Ceramics in total hip arthroplasty:history, mechanical properties, clinicalresults, and current manufacturing state of the art. Semin Arthroplast 9:114-122
66. De Aza A, Chevalier J, Fantozzi G et al (2002) Crack growth resistance of alumina, zirconia and zirconia toughened alumina ceramics for joint prostheses. Biomaterials 23(3):937-945
67. Helmer J, Driskell T (1969) Research on bioceramics. In:Symposium on use of ceramics as surgical implants, South Carolina
68. Christel P, Meunier A, Dorlot JM et al (1988) Biomechanical compatibility and design of ceramic implants for orthopedic surgery. Ann NY Acad Sci 523(1):234-256
69. Chevalier J (2006) What future for zirconia as a biomaterial? Biomaterials 27(4):535-543
70. Hummer CD, Rothman RH, Hozack WJ (1995) Catastrophic failure of modular zirconia-ceramic femoral head components after total hip arthroplasty. J Arthroplasty 10(6):848-850
71. Best S, Porter A, Thian E et al (2008) Bioceramics:past, present and for the future. J Eur Ceram Soc 28(7):1319-1327
72. Fathi M, Hanifi A, Mortazavi V (2008) Preparation and bioactivity evaluation of bone-like hydroxyapatite nanopowder. J Mater Process Technol 202(1):536-542
73. LeGeros RZ (2002) Properties of osteoconductive biomaterials:calcium phosphates. Clin Orthop Relat Res 395:81-98
74. Ducheyne P, Cuckler JM (1992) Bioactive ceramic prosthetic coatings. Clin Orthop Relat Res 276:102-114
75. Mohseni E, Zalnezhad E, Bushroa AR (2014) Comparative investigation on the adhesion of hydroxyapatite coating on Ti-6Al-4V implant:a review paper. Int J Adhes Adhes 48:238-257
76. Hench LL, Splinter RJ, Allen W et al (1971) Bonding mechanisms at the interface of ceramic prosthetic materials. J Biomed Mater Res Part A 5(6):117-141
77. Jarcho M, Kay JF, Gumaer KI et al (1977) Tissue, cellular and subcellular events at a bone-ceramic hydroxylapatite interface. J Bioeng 1(2):79-92
78. Bartolo P, Kruth JP, Silva J et al (2012) Biomedical production of implants by additive electro-chemical and physical processes. CIRP Ann Manuf Technol 61(2):635-655
79. Poser R, Magee F, Kay J et al (1990) In-vivo characterization of a hydroxylapatite coating. In:Transactions of the 16th annual meeting of the society for biomaterials, 1990, p 170
80. Murr L, Amato K, Li S et al (2011) Microstructure and mechanical properties of open-cellular biomaterials prototypes for total knee replacement implants fabricated by electron beam melting. J Mech Behav Biomed Mater 4(7):1396-1411
81. Murr L, Quinones S, Gaytan S et al (2009) Microstructure and mechanical behavior of Ti-6Al-4V produced by rapid-layer manufacturing, for biomedical applications. J Mech Behav Biomed Mater 2(1):20-32
82. Lampman S (1990) Wrought titanium and titanium alloys. ASM Int Metals Handb Tenth Edn 2:592-633
83. Balagna C, Faga M, Spriano S (2012) Tantalum-based multilayer coating on cobalt alloys in total hip and knee replacement. Mater Sci Eng C 32(4):887-895
84. Jovanovic M, Tadic S, Zec S et al (2006) The effect of annealing temperatures and cooling rates on microstructure and mechanical properties of investment cast Ti-6Al-4V alloy. Mater Des 27(3):192-199
85. Lin CW, Ju CP, Lin JH (2005) A comparison of the fatigue behavior of cast Ti-7.5 Mo with c.p. titanium, Ti-6Al-4V and Ti-13Nb-13Zr alloys. Biomaterials 26(16):2899-2907
86. Harrysson OL, Cansizoglu O, Marcellin-Little DJ et al (2008) Direct metal fabrication of titanium implants with tailored materials and mechanical properties using electron beam melting technology. Mater Sci Eng C 28(3):366-373
87. Eisen W, Ferguson B, German R et al (1998) Powder metal technologies and applications. In:Narayan R (ed) ASM handbook, vol 7. ASM International, USA, pp 308-2096
88. Davim JP (2008) Machining:fundamentals and recent advances. Springer, New York
89. Dewidar MM, Yoon HC, Lim JK (2006) Mechanical properties of metals for biomedical applications using powder metallurgy process:a review. Met Mater Int 12(3):193-206
90. Kuboki Y, Takita H, Kobayashi D et al (1998) BMP-induced osteogenesis on the surface of hydroxyapatite with geometrically feasible and nonfeasible structures:topology of osteogenesis. J Biomed Mater Res Part A 39(2):190-199
91. Vasconcellos LMRd, Oliveira MVd, Graça MLdA et al (2008) Porous titanium scaffolds produced by powder metallurgy for biomedical applications. Mater Res 11(3):275-280
92. Dewidar MM, Khalil KA, Lim J (2007) Processing and mechanical properties of porous 316L stainless steel for biomedical applications. Trans Nonferr Metals Soc China 17(3):468-473
93. Seah K, Thampuran R, Teoh S (1998) The influence of pore morphology on corrosion. Corros Sci 40(4-5):547-556
94. Ryan G, Pandit A, Apatsidis DP (2006) Fabrication methods of porous metals for use in orthopaedic applications. Biomaterials 27(13):2651-2670
95. Ning C, Zhou Y (2002) In vitro bioactivity of a biocomposite fabricated from HA and Ti powders by powder metallurgy method. Biomaterials 23(14):2909-2915
96. Gradzka-Dahlke M, Dabrowski J, Dabrowski B (2008) Modification of mechanical properties of sintered implant materials on the base of Co-Cr-Mo alloy. J Mater Process Technol 204(1):199-205
97. Elahinia MH, Hashemi M, Tabesh M et al (2012) Manufacturing and processing of NiTi implants:a review. Prog Mater Sci 57(5):911-946
98. Gong X, Anderson T, Chou K (2012) Review on powder-based electron beam additive manufacturing technology. In:ASME/ISCIE international symposium on flexible automation. American Society of Mechanical Engineers, pp 507-515
99. Frazier WE (2014) Metal additive manufacturing:a review. J Mater Eng Perform 23(6):1917-1928
100. Heinl P, Rottmair A, Körner C et al (2007) Cellular titanium by selective electron beam melting. Adv Eng Mater 9(5):360-364
101. Heinl P, Müller L, Körner C et al (2008) Cellular Ti-6Al-4V structures with interconnected macro porosity for bone implants fabricated by selective electron beam melting. Acta Biomater 4(5):1536-1544
102. Murr L, Gaytan S, Medina F et al (2010) Next-generation biomedical implants using additive manufacturing of complex, cellular and functional mesh arrays. Philos Trans R Soc Lond A Math Phys Eng Sci 368(1917):1999-2032
103. Kruth JP, Levy G, Klocke F et al (2007) Consolidation phenomena in laser and powder-bed based layered manufacturing. CIRP Ann Manuf Technol 56(2):730-759
104. Yadroitsev I, Bertrand P, Smurov I (2007) Parametric analysis of the selective laser melting process. Appl Surf Sci 253(19):8064-8069
105. Hao L, Dadbakhsh S, Seaman O et al (2009) Selective laser melting of a stainless steel and hydroxyapatite composite for load-bearing implant development. J Mater Process Technol 209(17):5793-5801
106. Wang Y, Shen Y, Wang Z et al (2010) Development of highly porous titanium scaffolds by selective laser melting. Mater Lett 64(6):674-676
107. Liverani E, Fortunato A, Leardini A et al (2016) Fabrication of Co-Cr-Mo endoprosthetic ankle devices by means of selective laser melting (SLM). Mater Des 106:60-68
108. Xin XZ, Chen J, Xiang N et al (2013) Surface properties and corrosion behavior of Co-Cr alloy fabricated with selective laser melting technique. Cell Biochem Biophys 67(3):983-990
109. Wilkes J, Hagedorn YC, Meiners W et al (2013) Additive manufacturing of ZrO₂-Al₂O₃ ceramic components by selective laser melting. Rapid Prototyp J 19(1):51-57
110. Zhang L, Klemm D, Eckert J et al (2011) Manufacture by selective laser melting and mechanical behavior of a biomedical Ti-24Nb-4Zr-8Sn alloy. Scr Mater 65(1):21-24
111. Pattanayak DK, Fukuda A, Matsushita T et al (2011) Bioactive Ti metal analogous to human cancellous bone:fabrication by selective laser melting and chemical treatments. Acta Biomater 7(3):1398-1406
112. Weißmann V, Bader R, Hansmann H et al (2016) Influence of the structural orientation on the mechanical properties of selective laser melted Ti6Al4V open-porous scaffolds. Mater Des 95:188-197
113. Mueller B (2012) Additive manufacturing technologies:rapid prototyping to direct digital manufacturing. Assem Autom 32(2):151-154
114. Turger A, Köhler J, Denkena B et al (2013) Manufacturing conditioned roughness and wear of biomedical oxide ceramics for all-ceramic knee implants. Biomed Eng Online 12(1):84. https://doi.org/10.1186/1475-925X-12-84
115. Hilerio I, Mathia T, Alepee C (2004) 3D measurements of the knee prosthesis surfaces applied in optimizing of manufacturing process. Wear 257(12):1230-1234
116. Sidpara AM, Jain V (2012) Nanofinishing of freeform surfaces of prosthetic knee joint implant. Proc Inst Mech Eng Part B J Eng Manuf 226(11):1833-1846
117. Denkena B, de Leon L, Turger A et al (2010) Prediction of contact conditions and theoretical roughness in manufacturing of complex implants by toric grinding tools. Int J Mach Tools Manuf 50(7):630-636
118. Jain V (2008) Abrasive-based nano-finishing techniques:an overview. Mach Sci Technol 12(3):257-294
119. Zhang D, Li C, Jia D et al (2014) Grinding model and material removal mechanism of medical nanometer zirconia ceramics. Recent Pat Nanotechnol 8(1):2-17
120. Ohmori H, Nakagawa T (1995) Analysis of mirror surface generation of hard and brittle materials by ELID (electronic inprocess dressing) grinding with superfine grain metallic bond wheels. CIRP Ann Manuf Technol 44(1):287-290
121. Kotani H, Komotori J, Mizutani M et al (2009) Surface finishing and modification for cobalt-chromium-molybdenum alloy by electrolytic in-process dressing (ELID) grinding. In:5th international conference on leading edge manufacturing in 21st century, LEM 2009
122. Kotani H, Komotori J, Naruse T et al (2013) Development of a new grinding system for finishing of hemispherical inside surface. Int J Nanomanuf 9(1):77-86
123. Cheung C, Ho L, Charlton P et al (2010) Analysis of surface generation in the ultraprecision polishing of freeform surfaces. Pro Inst Mech Eng Part B J Eng Manuf 224(1):59-73
124. Zaborski S, Sudzik A, Wolyniec A (2011) Electrochemical polishing of total hip prostheses. Arch Civ Mech Eng 11(4):1053-1062
125. Zhang LC, Kiat E, Pramanik A(2009) A briefing on the manufacture of hip joint prostheses. In:12th international symposium on advances in abrasive technology (ISAAT2009). Gold Coast, Australia, 2009, pp 212-216
126. Basim GB, Ozdemir Z (2015) Chemical mechanical polishing implementation on dental implants. In:International conference on planarization/CMP technology (ICPT). IEEE, pp 1-4
127. Ozdemir Z, Ozdemir A, Basim G (2016) Application of chemical mechanical polishing process on titanium based implants. Mater Sci Eng C 68:383-396
128. Landolt D (1987) Fundamental aspects of electropolishing. Electrochim Acta 32(1):1-11
129. Hryniewicz T, Rokicki R, Rokosz K (2008) Co-Cr alloy corrosion behaviour after electropolishing and "magnetoelectropolishing" treatments. Mater Lett 62(17):3073-3076
130. Hryniewicz T, Rokosz K, Rokicki R et al (2015) Nanoindentation and XPS studies of titanium TNZ alloy after electrochemical polishing in a magnetic field. Materials 8(1):205-215
131. Hryniewicz T, Rokicki R, Rokosz K (2008) Surface characterization of AISI 316L biomaterials obtained by electropolishing in a magnetic field. Surf Coat Technol 202(9):1668-1673
132. Magaino S, Matlosz M, Landolt D (1993) An impedance study of stainless steel electropolishing. J Electrochem Soc 140(5):1365-1373
133. Habibzadeh S, Li L, Shum-Tim D et al (2014) Electrochemical polishing as a 316L stainless steel surface treatment method:towards the improvement of biocompatibility. Corros Sci 87:89-100
134. Fang F, Zhang X, Weckenmann A et al (2013) Manufacturing and measurement of freeform optics. CIRP Ann Manuf Technol 62(2):823-846
135. Sidpara A, Jain V (2013) Analysis of forces on the freeform surface in magnetorheological fluid based finishing process. Int J Mach Tools Manuf 69:1-10
136. De Wild M, Amacher F, Bradbury CR et al (2016) Investigation of structural resorption behavior of biphasic bioceramics with help of gravimetry, μCT, SEM, and XRD. J Biomed Mater Res B Appl Biomater 104(3):546-553
137. Vyas N, Sammons R, Addison O et al (2016) A quantitative method to measure biofilm removal efficiency from complex biomaterial surfaces using SEM and image analysis. Sci Rep 6:32694. https://doi.org/10.1038/srep32694
138. Weckenmann A, Estler T, Peggs G et al (2004) Probing systems in dimensional metrology. CIRP Ann Manuf Technol 53(2):657-684
139. Charlton P, Blunt L (2008) Surface and form metrology of polished "freeform" biological surfaces. Wear 264(5):394-399
140. Fang F, Zhang X, Gao W et al (2017) Nanomanufacturing-perspective and applications. CIRP Ann Manuf Technol 66(2):683-705
141. Schellekens P, Rosielle N, Vermeulen H et al (1998) Design for precision:current status and trends. CIRP Ann Manuf Technol 47(2):557-586
142. Brand U, Cao S, Hoffmann W et al (2001) A micro-probing system for dimensional metrology on microsystem components. In:International conference on European society for precision engineering and nanotechnology (EUSPEN). 2001, pp 266-269
143. Danzebrink HU, Koenders L, Wilkening G et al (2006) Advances in scanning force microscopy for dimensional metrology. CIRP Ann Manuf Technol 55(2):841-878
144. Seitavuopio P (2006) The roughness and imaging characterisation of different pharmaceutical surfaces. Dissertation, University of Helsinki. Dissertation, University of Helsninki, Finland
145. Nemes C, Rozlosnik N, Ramsden J (1999) Direct measurement of the viscoelasticity of adsorbed protein layers using atomic force microscopy. Phys Rev E 60(2):R1166
146. Savio E, Marinello F, Bariani P, Carmignato S (2007) Featureoriented measurement strategy in atomic force microscopy. CIRP Ann Manuf Technol 56(1):557-560
147. Tamkin Sr JM (2010) A study of image artifacts caused by structured mid-spatial frequency fabrication errors on optical surfaces. Dissertation, The University of Arizona, USA
148. Rudolph W, Kempe M (1997) Trends in optical biomedical imaging. J Mod Opt 44(9):1617-1642
149. Gale MFR, Landau MR, Hogert EN et al (2003) Changing surfaces-a theoretical and experimental approach. J Opt A Pure Appl Opt 6(2):187-192

[1]	Zhen Zhang, Rui He, Kuo Yang. A bioinspired path planning approach for mobile robots based on improved sparrow search algorithm[J]. Advances in Manufacturing, 2022, 10(1): 114-130.
[2]	Cheng-Wei Kang, Feng-Zhou Fang. State of the art of bioimplants manufacturing: part II[J]. Advances in Manufacturing, 2018, 6(2): 137-154.
[3]	Bao-Rui Li, Yi Wang, Ke-Sheng Wang. A novel method for the evaluation of fashion product design based on data mining[J]. Advances in Manufacturing, 2017, 5(4): 370-376.

State of the art of bioimplants manufacturing: part I

State of the art of bioimplants manufacturing: part I

PDF

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 3

编辑推荐

Metrics

本文评价