Concept development for innovative functionally graded lattice structures to absorb desired energy and impact

doi:10.1007/s40436-024-00542-9

Abstract

Abstract: Densification and plateau behavior of lattices can be manipulated by selectively grading the cells. Metallic lattices are the conventional choice for energy absorption, while the generated impact has not been the subject of interest. However, this is the crucial requirement for protective applications like mine-blast absorber for armor vehicles. Different gradient approaches have been examined in this study to find the method which not only controls the absorbed energy, but also keeps the impact level below the identified threshold. This includes available density gradients as well as an innovative gradient geometry for the structure. The concept of how each gradient approach influences the plateau behavior was discussed. A novel approach has been presented which enables tracking the impact magnitude during densification. Although, series density-gradient is a common approach to improve energy absorption in industry, the result of this study demonstrates that crushing the denser region of lattice may generate significantly larger impact. Instead, arranging density gradient cells parallelly can absorb higher energy, while the increase in impact is not significant. An innovative design is presented for lattice structure with gradient geometry. It starts absorbing energy at very low impact and ends with significantly higher absorbed energy at full compaction. To expand the domain of application and effectiveness, new gradient approach was proposed by combining geometry and density grading. It was demonstrated that this highly efficient and flexible design configuration could reduce the activation impact by 94% with descending arrangement and double the absorbed energy by ascending arrangement. This was achieved while the impact magnitude was kept at a reasonable level. In addition, design parameters can be adjusted for desired level of energy and impact for particular application.

The full text can be downloaded at https://doi.org/10.1007/s40436-024-00542-9

Key words: Gradient lattice, Energy absorption, Impact absorption, Energy-impact absorption diagram, Plateau behavior

Mohammad Reza Vaziri Sereshk, Eric J. Faierson. Concept development for innovative functionally graded lattice structures to absorb desired energy and impact[J]. Advances in Manufacturing, 2025, 13(4): 799-812.

TrendMD

References

[1] Yin H, Zhang W, Zhu L et al (2023) Review on lattice structures for energy absorption properties. Compos Struct 304(1):116397. https://doi.org/10.1016/S0263822322011291
[2] Plocher J, Panesar A (2020) Effect of density and unit cell size grading on the stiffness and energy absorption of fibre-reinforced functionally graded lattice structures. Addit Manuf 33:101171. https://doi.org/10.1016/S2214860420305431
[3] Rahman H, Yarali E, Zolfagharian A et al (2021) Energy absorption and mechanical performance of functionally graded soft-hard lattice structures. Mater 14:1366. https://doi.org/10.3390/ma14061366
[4] Yang L, Sui L, Li X et al (2021) Sandwich plates with gradient lattice cores subjected to air blast loadings. Mech Adv Mater Struct 28(13):1355-1366
[5] McShane GJ, Deshpande VS, Fleck NA (2007) The underwater blast resistance of metallic sandwich beams with prismatic lattice cores. J Appl Mech 74:352-364
[6] Maskery I, Hussey A, Panesar A et al (2017) An investigation into reinforced and functionally graded lattice structures. J Cell Plast 53(2):151-165
[7] Al-Saedi DSJ, Masood SH (2018) Mechanical performance of functionally graded lattice structures made with selective laser melting 3D printing. IOP Conf Ser: Mater Sci Eng 433:012078. https://doi.org/10.1088/1757-899X/433/1/012078
[8] Al-Saedi DSJ, Masood SH, Faizan-Ur-Rab M et al (2018) Mechanical properties and energy absorption capability of functionally graded F2BCC lattice fabricated by SLM. Mater Des 144:32-44
[9] Wang E, Gardner N, Shukla A (2009) The blast resistance of sandwich composites with stepwise graded cores. Int J Solids Struct 46:3492-3502
[10] Gardner N, Wang E, Kumar P et al (2011) Blast mitigation in a sandwich composite using graded core and polyurea interlayer. Exp Mech 52(2):119-133
[11] Kelly M, Arora H, Worley A et al (2016) Sandwich panel cores for blast applications: materials and graded density. Exp Mech 56:523-544
[12] Yang L, Han X, Feng L et al (2020) Numerical investigations on blast resistance of sandwich panels with multilayered graded hourglass lattice cores. J Sandw Struct Mater 22(7):2139-2156
[13] Ramasamy A, Masouros SD, Newell N et al (2011) In-vehicle extremity injuries from improvised explosive devices: current and future foci. Philos Trans R Soc Lond B Biol Sci 366(1562):160-170
[14] Rigby SE, Fay SD, Clarke SD et al (2016) Measuring spatial pressure distribution from explosives buried in dry Leighton Buzzard sand. Int J Impact Eng 96:89-104
[15] Santosa SP, Arifurrahaman F, Izzudin MH et al (2017) Response analysis of blast impact loading of metal-foam sandwich panels. Procedia Eng 173:495-502
[16] Farajzadeh KS, Duckworth H, Galvanetto U et al (2019) The effects of topology and relative density of lattice liners on traumatic brain injury mitigation. J Biomech 97:109376. https://doi.org/10.1016/j.jbiomech.2019.109376
[17] Singh D, Kiran R, Chawla K et al (2022) Determination of multi-physics effective properties, and actuation response of triply periodic minimal surface based novel photo strictive composites: a finite element analysis. Int J Eng Sci 178:103726. https://doi.org/10.1016/S0020722522000957
[18] Chawla K, Kiran R (2022) Numerical predictions for the effect of negative Poisson’s ratio on thermoelastic properties of triply periodic minimal surface-based composites. Results Mater 14:100273. https://doi.org/10.1016/S2590048X22000218
[19] Sengsri P, Fu H, Kaewunruen S (2022) Mechanical properties and energy-absorption capability of a 3D-printed TPMS sandwich lattice model for meta-functional composite bridge bearing applications. J Compos Sci 6:71. https://doi.org/10.3390/jcs6030071
[20] Yu S, Sun J, Bai J (2019) Investigation of functionally graded TPMS structures fabricated by additive manufacturing. Mater Des 182:108021. https://doi.org/10.1016/S0264127519304599
[21] Gibson L, Ashby M (1997) Cellular solids: structure and properties. Cambridge University Press
[22] Vaziri-Sereshk MR, Faierson EJ (2024) Improvement in energy absorption of additively manufactured lattice structures after modification of collapse mechanisms. J Adv Manuf Technol 130:1617-1633
[23] Vaziri-Sereshk MR, Faierson E (2022) Study of defects and dimensional accuracy to determine manufacturability thresholds for laser powder bed fusion of Ti-6Al-4V lattices. J Adv Manuf Technol 123:3795-3806
[24] Gangireddy S, Faierson EJ, Mishra RS (2018) Influences of post-processing, location, orientation, and induced porosity on the dynamic compression behavior of Ti-6Al-4V alloy built through additive manufacturing. J Dyn Behav Mater 4:441-451
[25] ISO 13314, Mechanical testing of metals-ductility testing-compression testing for porous and cellular metals, https://www.iso.org/standard/53669.html. Accessed 22 Dec 2023
[26] McKown S, Shen Y, Brookes WK et al (2008) The quasi-static and blast loading response of lattice structures. Int J Impact Eng 35:795-810
[27] Tancogne-Dejean T, Spierings AB, Mohr D (2016) Additively-manufactured metallic micro-lattice materials for high specific energy absorption under static and dynamic loading. Acta Mater 116:14-28
[28] Ozdemir Z, Hernandez-Nava E, Tyas A et al (2016) Energy absorption in lattice structures in dynamics: experiments. Int J Impact Eng 89:49-61
[29] Harris JA, Winter RE, McShane GJ (2017) Impact response of additively manufactured metallic hybrid lattice materials. Int J Impact Eng 104:177-191
[30] Xiao LJ, Song WD (2018) Additively-manufactured functionally graded Ti-6Al-4V lattice structures with high strength under static and dynamic loading: experiments. Int J Impact Eng 111:255-272
[31] Bai L, Gong C, Chen X et al (2021) Quasi-static compressive responses and fatigue behaviour of Ti-6Al-4V graded lattice structures fabricated by laser powder bed fusion. Mater Des 210:110110. https://doi.org/10.1016/j.matdes.2021.110110
[32] Mora SDC, Heydari AA, Guagliano M et al (2022) Numerical investigation of Ti6Al4V gradient lattice structures with tailored mechanical response. Adv Eng Mater 24:2101760. https://doi.org/10.1002/adem.202101760
[33] Choy SY, Sun CN, Leong KF et al (2017) Compressive properties of functionally graded lattice structures manufactured by selective laser melting. Mater Des 131:112-120
[34] Zhao M, Zhang DZ, Liu F et al (2020) Mechanical and energy absorption characteristics of additively manufactured functionally graded sheet lattice structures with minimal surfaces. Int J Mech Sci 167:105262. https://doi.org/10.1016/j.ijmecsci.2019.105262
[35] Ma X, Zhang DZ, Zhao M et al (2022) Mechanical and energy absorption properties of functionally graded lattice structures based on minimal curved surfaces. J Adv Manuf Technol 118:995-1008