Experimental technique to analyze the influence of cutting conditions on specific energy consumption during abrasive metal cutting with thin discs

doi:10.1007/s40436-021-00361-2

Abstract

Abstract: Specific energy consumption is an important indicator for a better understanding of the machinability of materials. The present study aims to estimate the specific energy consumption for abrasive metal cutting with ultra-thin discs at comparatively low and medium feed rates. Using an experimental technique, the cutting power was measured at four predefined feed rates for S235JR, intermetallic Fe-Al(40%), and C45K with different thermal treatments. The variation in the specific energy consumption with the material removal rate was analyzed through an empirical model, which enabled us to distinguish three phenomena of energy dissipation during material removal. The thermal treatment and mechanical properties of materials have a significant impact on the energy consumption pattern, its corresponding components, and cutting power. Ductile materials consume more specific cutting energy than brittle materials. The specific cutting energy is the minimum energy required to remove the material, and plowing energy is found to be the most significant phenomenon of energy dissipation.

The full text can be downloaded at https://link.springer.com/article/10.1007/s40436-021-00361-2

Key words: Specific cutting energy, Specific energy consumption, Metal cutting with abrasive disc, Abrasive cut off operation, Cutting intermetallic alloy Fe-Al (40%)

Muhammad Rizwan Awan, Hernán A. González Rojas, José I. Perat Benavides, Saqib Hameed. Experimental technique to analyze the influence of cutting conditions on specific energy consumption during abrasive metal cutting with thin discs[J]. Advances in Manufacturing, 2022, 10(2): 260-271.

TrendMD

References

1. IEO (2018) International Energy Outlook 2018 ( IEO2018 ) Key takeaways. In: U.S. Energy Inf. Adm. https://www.eia.gov/pressroom/presentations/capuano_07242018.pdf. Accessed 2 Jan, 2021
2. Rahimifard S, Seow Y, Childs T (2010) Minimising embodied product energy to support energy efficient manufacturing. CIRP Ann Manuf Technol 59(1):25–28
3. Yuan C, Zhai Q, Dornfeld D (2012) A three dimensional system approach for environmentally sustainable manufacturing. CIRP Ann Manuf Technol 61:39–42
4. Zhang YJ (2014) Energy efficiency techniques in machining process: a review. Int J Adv Manuf Technol 71(5/8):1123–1132
5. He Y, Liu F, Wu T et al (2012) Analysis and estimation of energy consumption for numerical control machining. Proc Inst Mech Eng Part B J Eng Manuf 226:255–266
6. Malkin S, Guo C (2008) Grinding technology: theory and applications of machining with abrasives. Industrial Press, New York
7. Ding H, Guo D, Cheng K et al (2014) An investigation on quantitative analysis of energy consumption and carbon footprint in the grinding process. Proc Inst Mech Eng Part B J Eng Manuf 228:950–956
8. Komanduri R, Iyengar S (2001) Conventional and super abrasive materials. In: encyclopedia of materials: science and technology, 2nd ed. Pergamon, pp 1629–1651
9. Nelson JA, Westrich RM (1974) Abrasive cutting in metallography. In: Metallographic specimen preparation. Springer, US, pp 41–54
10. Kannappan S, Malkin S (1972) Effects of grain size and operating parameters on the mechanics of grinding. J Manuf Sci Eng 94(3):833–842
11. Öpöz TT, Chen X (2012) Experimental investigation of material removal mechanism in single grit grinding. Int J Mach Tools Manuf 63:32–40
12. Stachowiak GW, Batchelor, Andrew WGB (2004) Experimental methods in tribology: Introduction. Tribol Ser 44:1–12
13. Rowe WB (2018) Towards high productivity in precision grinding. Inventions 3(2):24. https://doi.org/10.3390/inventions3020024
14. Nápoles AA, González RH, Sánchez EA et al (2019) Model based on an effective material-removal rate to evaluate specific energy consumption in grinding. Materials 12:939. https://doi.org/10.3390/ma12060939
15. Masoumi H, Safavi SM, Salehi M (2014) Grinding force, specific energy and material removal mechanism in grinding of HVOF-sprayed WC-Co-Cr coating. Mater Manuf Process 29:321–330
16. Singh V, Venkateswara RP, Ghosh S (2012) Development of specific grinding energy model. Int J Mach Tools Manuf 60:1–13
17. Shaw MC (1996) Energy conversion in cutting and grinding. CIRP Ann Manuf Technol 45:101–104
18. Malkin S, Joseph N (1975) Minimum energy in abrasive processes. Wear 32:15–23
19. Shaw MC, Farmer DA, Nakayama K (1967) Mechanics of the abrasive cutoff operation. J Manuf Sci Eng Trans ASME 89(3):495–502
20. Turchetta S (2010) Cutting force in stone machining by diamond disk. Adv Mater Sci Eng 2010:631437. https://doi.org/10.1155/2010/631437
21. Azizi A, Mohamadyari M (2015) Modeling and analysis of grinding forces based on the single grit scratch. Int J Adv Manuf Technol 78:1223–1231
22. Brach K, Pai DM, Ratterman E et al (1988) Grinding forces and energy. J Manuf Sci Eng 110:25–31
23. Jain VK, Mote RG (2005) On the temperature and specific energy during electrodischarge diamond grinding (EDDG). Int J Adv Manuf Technol 26:56–67
24. Villagomez-Galindo M, Torre C, Romo-Castañeda JC et al (2016) Casting Fe-Al-based intermetallics alloyed with Li and Ag. J Mater Res 31:2473–2481
25. Alvi A (2018) S235JR non-alloy quality structural steel. https://www.materialgrades.com/s235jr-non-alloy-quality-structural-steel-2062.html. Accessed 10 May 2020
26. Iman W (2018) C45 medium carbon steel grade. Jul 2018. https://www.materialgrades.com/c45-medium-carbon-steel-grade-2082.html. Accessed 10 May 2020
27. 3M (2020) 3M, cut and grind wheel. https://www.3m.com/3M/en_US/metalworking-us/applications/cutting/. Accessed 3 Mar 2020
28. Wurm JD (1984) Machinist (AFSC 42750). Extension Course Institute, Air University
29. Sivasankar B (2008) Engineering chemistry. Tata McGrawHill New Delhi
30. Stepper motor or servomotor: Which should it be? https://www.motioncontroltips.com/stepper-motor-servomotor. Accessed 9 Jan 2021
31. Rowe WB (2014) Principles of modern grinding technology. Elsevier
32. García de Jalón J (1994) kinematic and dynamic simulation of multibody systems: the real-time challenge
33. Gutowski T, Dahmus J, Thiriez A (2006) Electrical energy requirements for manufacturing processes. In: Proceedings of the 13th CIRP international conference on life cycle engineering, 31 May – 2 June, 2006, Paris, France, pp 623–638
34. Kara S, Li W (2011) Unit process energy consumption models for material removal processes. CIRP Ann Manuf Technol 60(1):37–40
35. Li W, Winter M, Kara S et al (2012) Eco-efficiency of manufacturing processes: a grinding case. CIRP Ann Manuf Technol 61:59–62
36. Marinescu ID, Rowe WB, Dimitrov B et al (2004) Tribology of abrasive machining processes. William Andrew Inc, New York, US
37. Verhoeven J (2007) Steel metallurgy for the non-metallurgist. ASM International, Almere
38. Larson B, Schmerr L (2003) Collaboration for nondestructive testing education—extending the reach. AIP Conf Proc 657(1):1899–1904
39. Astakhov VP, Outeiro JC (2008) Metal cutting mechanics, finite element modelling. In: Machining: fundamentals and recent advances. Springer, London, pp 1–27
40. Buehler MJ (2008) Atomistic modeling of materials failure. Springer Science & Business Media
41. Yousefi R, Ichida Y (2000) Study on ultra-high-speed cutting of aluminum alloy: formation of welded metal on the secondary cutting edge of the tool and its effects on the quality of finished surface. Precis Eng 24:371–376
42. Hameed S, Rojas HAG, Benavides JIP et al (2018) Influence of the regime of electropulsing-assisted machining on the plastic deformation of the layer being cut. Materials 11(6):886. https://doi.org/10.3390/ma11060886
43. Morris DG, Muñoz-Morris MA, Requejo LM (2007) Work hardening in Fe-Al alloys. Mater Sci Eng A 460:163–173
44. Liu CT, George EP, Maziasz PJ et al (1998) Recent advances in B2 iron aluminide alloys: deformation, fracture and alloy design. Mater Sci Eng A 258:84–98
45. Saigal A, Yang W (2003) Analysis of milling of iron aluminides. J Mater Process Technol 132:149–156
46. Zhang T, Jiang F, Yan L et al (2018) Research on the size effect of specific cutting energy based on numerical simulation of single grit scratching. J Manuf Sci Eng 140(7):071017. https://doi.org/10.1115/1.4039916
47. Linke B, Garretson I, Torner FM (2017) Grinding energy modeling based on friction, plowing and shearing. J Manuf Sci Eng 139(12):121009. https://doi.org/10.1115/1.4037239
48. Wu C, Li B, Yang J et al (2016) Prediction of grinding force for brittle materials considering co-existing of ductility and brittleness. Int J Adv Manuf Technol 87:1967–1975
49. Sinha MK, Ghosh S, Paruchuri VR (2019) Modelling of specific grinding energy for Inconel 718 superalloy. Proc Inst Mech Eng Part B J Eng Manuf 233:443–460
50. Kupka M (2006) High temperature strengthening of the FeAl intermetallic phase-based alloy. Intermetallics 14:149–155
51. George EP, Baker I (1998) Thermal vacancies and the yield anomaly of FeAl. Intermetallics 6:759–763