Tool geometry based prediction of critical thrust force while drilling carbon fiber reinforced polymers

doi:10.1007/s40436-015-0129-y

Advances in Manufacturing ›› 2015, Vol. 3 ›› Issue (4): 300-308.doi: 10.1007/s40436-015-0129-y

Tool geometry based prediction of critical thrust force while drilling carbon fiber reinforced polymers

Y. Karpat¹, O. Bahtiyar²

1 Department of Industrial Engineering, Bilkent University, Ankara 06800, Turkey;
2 Turkish Aerospace Industries Inc., Ankara 06980, Turkey

收稿日期:2015-08-28 修回日期:2015-11-06 出版日期:2015-12-25 发布日期:2015-12-08
通讯作者: Y. Karpat E-mail:ykarpat@bilkent.edu.tr

Tool geometry based prediction of critical thrust force while drilling carbon fiber reinforced polymers

Y. Karpat¹, O. Bahtiyar²

1 Department of Industrial Engineering, Bilkent University, Ankara 06800, Turkey;
2 Turkish Aerospace Industries Inc., Ankara 06980, Turkey

Received:2015-08-28 Revised:2015-11-06 Online:2015-12-25 Published:2015-12-08
Contact: Y. Karpat E-mail:ykarpat@bilkent.edu.tr

摘要/Abstract

摘要： Carbon fiber reinforced polymers (CFRPs) are known to be difficult to cut due to the abrasive nature of carbon fibers and the low thermal conductivity of the polymer matrix. Polycrystalline diamond (PCD) drills are commonly employed in CFRP drilling to satisfy hole quality conditions with an acceptable tool life. Drill geometry is known to be influential on the hole quality and productivity of the process. Considering the variety of CFRP laminates and available PCD drills on the market, selecting the suitable drill design and process parameters for the CFRP material being machined is usually performed through trial and error. In this study, machining performances of four different PCD drills are investigated. A mechanistic model of drilling is used to reveal trade-offs in drill designs and it is shown that it can be used to select suitable feed rate for a given CFRP drilling process.

关键词: Machining, Drilling, Carbon fiber reinforced polymer (CFRP), Polycrystalline diamond (PCD), Delamination

Abstract: Carbon fiber reinforced polymers (CFRPs) are known to be difficult to cut due to the abrasive nature of carbon fibers and the low thermal conductivity of the polymer matrix. Polycrystalline diamond (PCD) drills are commonly employed in CFRP drilling to satisfy hole quality conditions with an acceptable tool life. Drill geometry is known to be influential on the hole quality and productivity of the process. Considering the variety of CFRP laminates and available PCD drills on the market, selecting the suitable drill design and process parameters for the CFRP material being machined is usually performed through trial and error. In this study, machining performances of four different PCD drills are investigated. A mechanistic model of drilling is used to reveal trade-offs in drill designs and it is shown that it can be used to select suitable feed rate for a given CFRP drilling process.

Key words: Machining, Drilling, Carbon fiber reinforced polymer (CFRP), Polycrystalline diamond (PCD), Delamination

Y. Karpat, O. Bahtiyar. Tool geometry based prediction of critical thrust force while drilling carbon fiber reinforced polymers[J]. Advances in Manufacturing, 2015, 3(4): 300-308.

参考文献

1. König W, Wulf C, Graß P et al (1985) Machining of fibre reinforced plastics. CIRP Ann Manuf Technol 34(2):537-548

2. Ho-cheng H, Dharan CKH (1990) Delamination during drilling in composite laminates. J Manuf Sci Eng 112(3):236-239

3. Zhang LB, Wang LJ, Liu XY (2001) A mechanical model for predicting critical thrust forces in drilling composite laminates. Proc Inst Mech Eng Part B 215(2):135-146

4. Faraz A, Biermann D, Weinert K (2009) Cutting edge rounding: an innovative drill wear criterion in drilling CFRP composite laminates. Int J Mach Tools Manuf 49(15):1185-1196

5. Karpat Y, De?er B, Bahtiyar O (2012) Drilling thick fabric woven CFRP laminates with double point angle drills. J Mater Process Technol 212(10):2117-2127

6. Shyha IS, Aspinwall DK, Soo SL et al (2009) Drill geometry and operating effects when cutting small diameter holes in CFRP. Int J Mach Tools Manuf 49(12):1008-1014

7. Abraõ AM, Rubio JCC, Faria PE et al (2008) The effect of cutting tool geometry on thrust force and delamination when drilling glass fibre reinforced plastic composite. Mater Des 29(2):508-513

8. Duraõ LMP, Gonçalves DJS, Tavares JMRS et al (2010) Drilling tool geometry evaluation for reinforced composite laminates. Compos Struct 92(7):1545-1550

9. Karpat Y, De?er B, Bahtiyar O (2014) Experimental evaluation of polycrystalline diamond tool geometries while drilling carbon fiber-reinforced plastics. Int J Adv Manuf Technol 71(5-8):1295-1307

10. Lazar MB, Xirouchakis P (2013) Mechanical load distribution along the main cutting edges in drilling. J Mater Process Technol 213(2):245-260

11. Karpat Y, Bahtiyar O, De?er B et al (2014) A mechanistic approach to investigate drilling of UD-CFRP laminates with PCD drills. CIRP Annals-Manuf Technol 63(1):81-84

12. Meng Q, Zhang K, Cheng H et al (2015) An analytical method for predicting the fluctuation of thrust force during drilling of unidirectional carbon fiber reinforced plastics. J Compos Mater 49(6):699-711

13. Sadek A, Shi B, Meshreki M et al (2015) Prediction and control of drilling-induced damage in fibre-reinforced polymers using a new hybrid force and temperature modelling approach. CIRP Annals-Manuf Technol 64(1):89-92

14. Hocheng H, Tsao CC (2006) Effects of special drill bits on drilling-induced delamination of composite materials. Int J Mach Tools Manuf 46(12-13):1403-1416

15. Isbilir O, Ghassemieh E (2013) Numerical investigation of the effects of drill geometry on drilling induced delamination of carbon fiber reinforced composites. Compos Struct 105(8):126-133

16. Karpat Y, Bahtiyar O (2015) Comparative analysis of PCD drill designs during drilling of CFRP laminates. Proceedings of the 15th CIRP conference on modelling of machining operations, Procedia Cirp, 31:316-321

[1]	Wei Zhao, Asif Iqbal, Ding Fang, Ning He, Qi Yang. Experimental study on the meso-scale milling of tungsten carbide WC-17.5Co with PCD end mills[J]. Advances in Manufacturing, 2020, 8(2): 230-241.
[2]	Xiang Zou, Hon-Yuen Tam, Hai-Yin Xu, Ke Shi. Flat-end tool orientation based on rotation-minimizing frame[J]. Advances in Manufacturing, 2019, 7(3): 257-269.
[3]	Shu-Tao Huang, Chao Li, Li-Fu Xu, Lin Guo, Xiao-Lin Yu. Variation characteristic of drilling force and influence of cutting parameter of SiCp/Al composite thin-walled workpiece[J]. Advances in Manufacturing, 2019, 7(3): 288-302.
[4]	Tian-Xun Xiu, Wei Wang, Kun Liu, Zhi-Yong Wang, Dao-Zhu Wei. Characteristics of force chains in frictional interface during abrasive flow machining based on discrete element method[J]. Advances in Manufacturing, 2018, 6(4): 355-375.
[5]	Saroj Kumar Padhi, S. S. Mahapatra, Rosalin Padhi, Harish Chandra Das. Performance analysis of a thick copper-electroplated FDM ABS plastic rapid tool EDM electrode[J]. Advances in Manufacturing, 2018, 6(4): 442-456.
[6]	Mukesh Kumar Sindhu, Debasish Nandi, Indrajit Basak. Electric discharge phenomenon in dielectric and electrolyte medium[J]. Advances in Manufacturing, 2018, 6(4): 457-464.
[7]	Lutfi Taner Tunc, Orkun Ozsahin. Use of inverse stability solutions for identification of uncertainties in the dynamics of machining processes[J]. Advances in Manufacturing, 2018, 6(3): 308-318.
[8]	Ehsan Jafarzadeh, Mohammad R. Movahhedy, Saeed Khodaygan, Mohammad Ghorbani. Prediction of machining chatter in milling based on dynamic FEM simulations of chip formation[J]. Advances in Manufacturing, 2018, 6(3): 334-344.
[9]	Mohammad Lotfi, Saeid Amini, Ihsan Yaseen Al-Awady. 3D numerical analysis of drilling process: heat, wear, and built-up edge[J]. Advances in Manufacturing, 2018, 6(2): 204-214.
[10]	V. G. Ladeesh, R. Manu. Effect of machining parameters on edge-chipping during drilling of glass using grinding-aided electrochemical discharge machining (G-ECDM)[J]. Advances in Manufacturing, 2018, 6(2): 215-224.
[11]	Somvir Singh Nain, Dixit Garg, Sanjeev Kumar. Evaluation and analysis of cutting speed, wire wear ratio, and dimensional deviation of wire electric discharge machining of super alloy Udimet-L605 using support vector machine and grey relational analysis[J]. Advances in Manufacturing, 2018, 6(2): 225-246.
[12]	Dipesh Popli, Meenu Gupta. Experimental study and optimization of cutting parameters in machining of super alloy with hybrid ultrasonic method[J]. Advances in Manufacturing, 2017, 5(3): 199-216.
[13]	Sandip Kunar, B. Bhattacharyya. Investigation on surface structuring generated by electrochemical micromachining[J]. Advances in Manufacturing, 2017, 5(3): 217-230.
[14]	Szymon Wojciechowski, Zbigniew Nowakowski, Radomir Majchrowski, Grzegorz Królczyk. Surface texture formation in precision machining of direct laser deposited tungsten carbide[J]. Advances in Manufacturing, 2017, 5(3): 251-260.
[15]	Ravindra Nath Yadav. Development and experimental investigation of duplex turning process[J]. Advances in Manufacturing, 2017, 5(2): 149-157.

Tool geometry based prediction of critical thrust force while drilling carbon fiber reinforced polymers

Tool geometry based prediction of critical thrust force while drilling carbon fiber reinforced polymers

PDF

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价