Modeling and simulation of percussive impact for robotic riveting system

doi:10.1007/s40436-014-0091-0

Abstract

Abstract: Riveting is one of the major joining methods used in assembly, and the robotic riveting has been gradually introduced into aircraft industry. In this paper, a method is presented for modeling and simulation of percussive robotic riveting. In percussive riveting, vibration always exists. When an impact force is employed, a forced vibration will be induced. If it resonates with a robot natural frequency, the vibration will cause damage to the robot. The main content of this paper is divided into three parts. Firstly, a robot dynamic model is established to compute the driving torque for each joint. Secondly, vibration responses under impact are analyzed for the percussive riveting process. Thirdly, the effect of riveting on robot vibration is studied over the robot workspace. The purpose of this paper is to discuss the suitable regions for riveting where the robot vibration is very minimal. It is shown that based on the presented method an appropriate trajectory can be planned for robotic riveting.

Key words: Robotic dynamics , Analysis , Vibration response, Impact force , Riveting

Shuai Guo,Song-Liang Nie, Feng-Feng Xi,Tao Song. Modeling and simulation of percussive impact for robotic riveting system[J]. Advances in Manufacturing, 2014, 2(4): 344-352.

TrendMD

References

1. Li YW, Xi FF, Behdinan K (2010) Dynamic modeling and simulation of percussive impact riveting for robotic automation. J Comput Nonlinear Dyn 5(2):021011
2. Qu W, Dong H, Ke Y (2011) Pose accuracy compensation technology in robot-aided aircraft assembly drilling process. Acta Aeronautica et Astronautica Sinica 32(10):1951–1960
3. Xiao H, Li Y, Zhang KF et al (2010) Multi-objective optimization method for automatic drilling and riveting sequence planning. Chin J Aeronaut 23(6):734–742
4. Bi S, Liang J (2011) Robotic drilling system for titanium structures. Int J Adv Manuf Technol 54(5/8):767–774
5. Olsson T, Robertsson A, Johansson R (2007) Flexible force control for accurate low-cost robot drilling. In: 2007 IEEE
international conference on robotics and automation, Roma, Italy,10–14 April 2007
6. Dhanaraj C, Sharan M (1995) Efficient modeling of rigid link robot dynamic problems with friction. Mech Mach Theory 30(5):749–764
7. Zhao Y, Bai Z (2010) Dynamics analysis of space robot manipulator with joint clearance. Acta Astronautica 68(7):1147–1155
8. KalyoncuM(2007) Mathematical modelling and dynamic response of a multi-straight-line path tracing flexible robot manipulator with rotating-prismatic joint. Appl Math Model 32(6):1087–1098
9. Shi ZX, Fung Eric HK, Li YC (1999) Dynamic modelling of a rigid-flexible manipulator for constrained motion task control. Appl Math Model 23(7):509–525
10. Knani J (2002) Dynamic modeling of flexible robotic mechanisms and adaptive robust control of trajectory computer simulation. Appl Math Model 26(12):1113–1124
11. Zhang C, Yu Y (2003) Dynamic modeling of robot arm with joint flexibility and link flexibility manipulating a constrained object. Chin J Mech Eng 39(6):9–12
12. Lee CSG, Lee BH, Nigam R (1982) An efficient formulation of robot arm dynamics for control analysis and manipulator design. Technical Reports of Robotics and Integrated Manufacturing, University of Michigan, Ann Arbor, Michigan
13. Boscariol P, Gasparetto A (2013) Model-based trajectory planning for flexible-link mechanisms with bounded jerk. Robot Comput Integr Manuf 8(29):90–99
14. Yin HB, Kobayashi Y, Hoshino Y et al (2011) Modeling and vibration analysis of flexible robotic arm under fast motion in consideration of nonlinearity. J Syst Des Dyn 5(5):909–924
15. XieX,Huang J, LiangZ(2013) Vibration reduction forflexible systems by command smoothing. Mech Syst Signal Process 8(39):461–470
16. Wang Y, Huang QB, Zhou MG et al (2006) Vibration response analysis of 2-DOF locally nonlinear systems based on the theory of modal super position. J Chongqing Univ (English Edition) 5(3):125–130

[1]	Yun-Song Lian, Chen-Liang Mu, Ming Liu, Hui-Feng Chen, Bin Yao. Three-dimensional numerical simulation of soft/hard composite-coated textured tools in dry turning of AISI 1045 steel [J]. Advances in Manufacturing, 2019, 7(2): 133-141.
[2]	Ning Li, Yong-Jie Chen, Dong-Dong Kong. Multi-response optimization of Ti-6Al-4V turning operations using Taguchi-based grey relational analysis coupled with kernel principal component analysis [J]. Advances in Manufacturing, 2019, 7(2): 142-154.
[3]	Jiang-Hua Deng, Feng Lyu, Ru-Ming Chen, Zhi-Song Fan. Influence of die geometry on self-piercing riveting of aluminum alloy AA6061-T6 to mild steel SPFC340 sheets [J]. Advances in Manufacturing, 2019, 7(2): 209-220.
[4]	Ali Kalyon, Mustafa Günay, Dursun Özyürek. Application of grey relational analysis based on Taguchi method for optimizing machining parameters in hard turning of high chrome cast iron [J]. Advances in Manufacturing, 2018, 6(4): 419-429.
[5]	Ramanuj Kumar, Ashok Kumar Sahoo, Purna Chandra Mishra, Rabin Kumar Das. Comparative study on machinability improvement in hard turning using coated and uncoated carbide inserts: part II modeling, multi-response optimization, tool life, and economic aspects [J]. Advances in Manufacturing, 2018, 6(2): 155-175.
[6]	V. G. Ladeesh, R. Manu. Effect of machining parameters on edge-chipping during drilling of glass using grinding-aided electrochemical discharge machining (G-ECDM) [J]. Advances in Manufacturing, 2018, 6(2): 215-224.
[7]	Somvir Singh Nain, Dixit Garg, Sanjeev Kumar. Evaluation and analysis of cutting speed, wire wear ratio, and dimensional deviation of wire electric discharge machining of super alloy Udimet-L605 using support vector machine and grey relational analysis [J]. Advances in Manufacturing, 2018, 6(2): 225-246.
[8]	Qiang He, An-Ling Li, Yuan Shen, Li-Li Li. Thermal optimization and experimental research of high-speed universal pulverizer [J]. Advances in Manufacturing, 2018, 6(1): 83-94.
[9]	Kundan K. Singh, Ramesh Singh. Chatter stability prediction in high-speed micromilling of Ti6Al4V via finite element based microend mill dynamics [J]. Advances in Manufacturing, 2018, 6(1): 95-106.
[10]	A. Pramanik, L. C. Zhang. Particle fracture and debonding during orthogonal machining of metal matrix composites [J]. Advances in Manufacturing, 2017, 5(1): 77-82.
[11]	Achilles Vairis, George Papazafeiropoulos, Andreas-Marios Tsainis. A comparison between friction stir welding, linear friction welding and rotary friction welding [J]. Advances in Manufacturing, 2016, 4(4): 296-304.
[12]	Song-Sheng Li, Yuan Shen, Qiang He. Study of the thermal influence on the dynamic characteristics of the motorized spindle system [J]. Advances in Manufacturing, 2016, 4(4): 355-362.
[13]	Shuai Guo, Yi Jin, Sheng Bao, Feng-Feng Xi. Accuracy analysis of omnidirectional mobile manipulator with mecanum wheels [J]. Advances in Manufacturing, 2016, 4(4): 363-370.
[14]	Thella Babu Rao. Optimizing machining parameters of wire-EDM process to cut Al7075/SiCp composites using an integrated statistical approach [J]. Advances in Manufacturing, 2016, 4(3): 202-216.
[15]	Prakash KumarSahu, Kanchan Kumari, Sukhomay Pal, Surjya K. Pal. Hybrid fuzzy-grey-Taguchi based multi weld quality optimization of Al/Cu dissimilar friction stir welded joints [J]. Advances in Manufacturing, 2016, 4(3): 237-247.