Experimental study and optimization of cutting parameters in machining of super alloy with hybrid ultrasonic method

doi:10.1007/s40436-017-0185-6

Abstract

Abstract:

Super alloys are intensively used in various industries, especially in the aerospace industry, because of their special characteristics. A number of holes are sometimes required to be drilled into super alloys for aircraft at their final stage assembly. In the present study, a hybrid ultrasonic machining method, called rotary ultrasonic machining (RUM), was successfully used in super alloy drilling. The empirical modeling of the process parameters of RUM was performed for the super alloy (Inconel 718) using an experimental design approach, called response surface methodology (RSM). Parameters, namely tool rotation, feed rate, ultrasonic power, and abrasive grit size, were selected as input variables. The others were kept constant. The performance was measured in terms of the machining rate and the surface roughness. The developed models were found to be reliable representatives of the experimental results with prediction errors less than ±5%. Moreover, the feed rate for the quality and productivity aspect was found to be the most critical factor. The optimized values of the machining rate and the surface roughness achieved through a multi-response optimization were 0.9 825 mm³/s and 0.951 μm, respectively.

The full text can be downloaded at https://link.springer.com/article/10.1007/s40436-017-0185-6

Key words: Super alloy, Rotary ultrasonic machining (RUM), Ultrasonic, Roughness, Machining

Dipesh Popli, Meenu Gupta. Experimental study and optimization of cutting parameters in machining of super alloy with hybrid ultrasonic method[J]. Advances in Manufacturing, 2017, 5(3): 199-216.

TrendMD

Add to citation manager EndNote|Reference Manager|ProCite|BibTeX|RefWorks

URL: https://www.aim.shu.edu.cn/EN/10.1007/s40436-017-0185-6

https://www.aim.shu.edu.cn/EN/Y2017/V5/I3/199

References

1. Davis JR, Associates (2000) ASM specialty handbook: nickel, cobalt, and their alloys. ASM International Handbook Committee
2. Nalbant M, Alt?n A, Gokkaya H (2007) The effect of cutting speed and cutting tool geometry on machinability properties of nickel-base Inconel 718 super alloys. Mater Des 28:1334- 1338
3. Khidhir BA, Mohamed B (2010) Machining of nickel based alloys using different cemented carbide tools. J Eng Sci Technol 5:264-271
4. Dreshfiezd RL (1970) Estimation of gamma phase composition in nickel-base superalloys (based on geometric analysis of a fourcomponent phase diagram). Nasa technical note
5. Zhou J, Bushlya V, Avdovic P et al (2012) Study of surface quality in high speed turning of Inconel 718 with uncoated and coated CBN tools. Int J Adv Manuf Technol 58:141-151
6. Bhatt A, Attia H, Vargas R et al (2010) Wear mechanisms of WC coated and uncoated tools in finish turning of Inconel 718. Tribol Int 43:1113-1121
7. Pei ZJ, Ferreira PM, Kapoor SG et al (1995) Rotary ultrasonic machining for face milling of ceramics. Int J Mach Tools Manuf 35:1033-1046
8. Zhang CL, Feng PF, Wu ZJ et al (2011) An experimental study on processing performance of rotary ultrasonic drilling of K9 glass. Adv Mater Res 230-232:221-225
9. Hu P, Zhang J, Pei ZJ et al (2002) Modeling of material removal rate in rotary ultrasonic machining: designed experiments. J Mater Process Technol 129:339-344
10. Lauwers B, Bleicher F, Haaf P (2010) Investigation of the process-material interaction in ultrasonic assisted grinding of ZrO₂ based ceramic materials. In: proceedings of 4th CIRP international conference on high performance cutting, 24-26 October 2010, pp 59-64
11. Li ZC, Jiao Y, Deines TW et al (2005) Rotary ultrasonic machining of ceramic matrix composites: feasibility study and designed experiments. Int J Mach Tools Manuf 45:1402-1411
12. Kataria R, Kumar J, Pabla BS (2015) Experimental investigation into the hole quality in ultrasonic machining of WC-Co composite. Mater Manuf Process 30:921-933
13. Singh RP, Singhal S (2016) Investigation of machining characteristics in rotary ultrasonic machining of alumina ceramic. Mater Manuf Process 6914(10426914):1176190
14. Singh RP, Singhal S (2016) Experimental investigation of machining characteristics in rotary ultrasonic machining of quartz ceramic. J Mater Des Appl 0:1-20
15. Singh RP, Singhal S (2016) Experimental study on rotary ultrasonic machining of alumina ceramic: microstructure analysis and multi-response optimization. Proc Inst Mech Eng Part L J Mater Des Appl 0:1-20
16. Churi NJ, Pei ZJ, Treadwell C (2006) Rotary ultrasonic machining of titanium alloy: effects of machining variables. Mach Sci Technol 10:301-321
17. Zou XT (2013) Cutting temperature in rotary ultrasonic machining of titanium: experimental study using novel FabryPerot fibre optic sensors. Int J Manuf Res 8:250-261
18. Lv D, Tang Y, Wang H et al (2013) Experimental investigations on subsurface damage in rotary ultrasonic machining of glass BK7. Mach Sci Technol 17:443-463
19. Feng Q, Cong WL, Pei ZJ et al (2012) Rotary ultrasonic machining of carbon fiber-reinforced polymer: feasibility study. Mach Sci Technol 16:380-398
20. Jiao Y, Liu WJ, Pei ZJ et al (2005) Study on edge chipping in rotary ultrasonic machining of ceramics: an integration of designed experiments and finite element method analysis. J Manuf Sci Eng 127:752-758
21. Zhang CL, Feng PF, Pei ZJ et al (2013) Rotary ultrasonic machining of sapphire: feasibility study and designed experiments. Key Eng Mater 589-590:523-528
22. Churi NJ, Pei ZJ, Shorter DC et al (2007) Rotary ultrasonic machining of silicon carbide: designed experiments. Int J Manuf Technol Manag 12:284-298
23. Debnath K, Singh I (2017) Low-frequency modulation-assisted drilling of carbon-epoxy composite laminates. J Manuf Process 25:262-273
24. Okamura K, Sasahara H, Segawa T et al (2006) Low-frequency vibration drilling of titanium alloy. JSME Int J Ser C 49:76-82
25. Torres A, Luis CJ, Puertas I (2015) Analysis of the influence of EDM parameters on surface finish, material removal rate, and electrode wear of an Inconel 600 alloy. Int J Adv Manuf Technol 80:123-140
26. Montgomery DC (2008) Design and analysis of experiments. Wiley, New York
27. Pi J, Yang G, Ye F (2013) Study on impact stress characteristics in ultrasonic cutting and brittle material removal mechanism. Adv Mater Res 753-755:287-297
28. Derringer G, Suich R (1980) Simultaneous optimization of several response variables. J Qual Technol 12(4):214-219

[1]	Yi-Fan Zhu, Peng-Feng Sheng, Qiu-Shi Huang, Li Wang, Jun Yu, Zhong Zhang, Zhan-Shan Wang. Theoretical and experimental study of the evolution of surface textures during wheel polishing with fluid cutting model [J]. Advances in Manufacturing, 2026, 14(2): 294-310.
[2]	Pei-Yao Cao, Hao Tong, Yong Li, Bao-Quan Li, Feng Yu. High-precision spindle head with combined function of rotation and inchworm feed for micro-EDM with WEDG [J]. Advances in Manufacturing, 2026, 14(2): 311-328.
[3]	Heng Luo, Zhao-Cheng Wei, Zhi-Gang Dong, Ren-Ke Kang, Yi-Dan Wang. High efficiency roughing process for the ultrasonic cutting of Nomex honeycomb cores [J]. Advances in Manufacturing, 2026, 14(2): 377-396.
[4]	Zhi-Gang Dong, Bao-Rong Li, Zhong-Wang Wang, Xiao-Guang Guo, Jian-Song Sun. Removal mechanism of RB-SiC using axial ultrasonic-assisted scratching [J]. Advances in Manufacturing, 2026, 14(2): 416-436.
[5]	Jie-Qiong Lin, Ming-Qi Guo, Shi-Xin Zhao, Ming-Ming Lu, Shuai-Jie Zhai, Yu-Cheng Li. Modelling and experimental study on brittle-to-ductile transition during ultrasonic elliptical vibration-assisted cutting of zirconia ceramics [J]. Advances in Manufacturing, 2026, 14(2): 437-451.
[6]	Tai-Min Luo, Jin Zhang, Chen-Jie Deng, Dai-Xin Luo, Gui-Bao Tao, Hua-Jun Cao. Green machining technology and application driven by digital intelligence: a review [J]. Advances in Manufacturing, 2026, 14(1): 43-102.
[7]	Yan-Jun Lu, Ming-Rong Guo, Yong-Qi Dai, Qiang Wang, Hu Luo. Experimental study on ultrasonic vibration-assisted grinding of quartz glass microchannel [J]. Advances in Manufacturing, 2025, 13(4): 701-717.
[8]	Zheng-Wen Nie, Jia-Bin Cao, Yi-Yang Zhao, Lin Zhang, Xun Liu, Yan Xu, Yan-Zheng Zhao. Efficient numerical-control simulation for multi-axis machining based on three-level grids [J]. Advances in Manufacturing, 2025, 13(4): 718-736.
[9]	Tong Zhu, Carman K. M. Lee, Sandy Suet To. Data-driven model for predicting machining cycle time in ultra-precision machining [J]. Advances in Manufacturing, 2025, 13(4): 831-846.
[10]	Chang-Feng Yao, Wen-Hao Tang, Liang Tan, Min-Chao Cui, Yun-Qi Sun, Tao Fan, Xu-Hang Gao. Surface softening mechanism based on microstructure analyses under ultrasonic impact condition for Ti-17 titanium alloy [J]. Advances in Manufacturing, 2025, 13(3): 562-583.
[11]	Hao Sun, Sheng-Qiang Zhao, Fang-Yu Peng, Rong Yan, Xiao-Wei Tang. Allowance distribution and parameters optimization for high-performance machining of low rigidity parts in multistage machining processes [J]. Advances in Manufacturing, 2025, 13(3): 584-605.
[12]	Peng Wang, Chang-Yong Yang, Ying-Ying Yuan, Yu-Can Fu, Wen-Feng Ding, Jiu-Hua Xu, Yong Chen. Study on the mechanism of burr formation in ultrasonic vibration-assisted honing 9Cr18MoV valve sleeve [J]. Advances in Manufacturing, 2025, 13(3): 606-619.
[13]	Lin Gu, Ke-Lin Li, Xiao-Ka Wang, Guo-Jian He. The effect of the slope angle and the magnetic field on the surface quality of nickel-based superalloys in blasting erosion arc machining [J]. Advances in Manufacturing, 2025, 13(3): 620-633.
[14]	Yi-Fan Li, Liang-Chi Zhang. Role of interatomic potentials in molecular dynamics simulations of silicon nanomachining [J]. Advances in Manufacturing, 2025, 13(2): 265-283.
[15]	Zhen-Jing Duan, Shuai-Shuai Wang, Shu-Yan Shi, Ji-Yu Liu, Yu-Heng Li, Zi-Heng Wang, Chang-He Li, Yu-Yang Zhou, Jin-Long Song, Xin Liu. Surface quality evaluation of cold plasma and NMQL multi-field coupling eco-friendly micro-milling 7075-T6 aluminum alloy [J]. Advances in Manufacturing, 2025, 13(1): 69-87.