Prediction of machining chatter in milling based on dynamic FEM simulations of chip formation

doi:10.1007/s40436-018-0228-7

Abstract

Abstract: Chatter vibration is a major obstacle in achieveing increased machining performance. In this research, a finite element model of chip formation in a 2D milling process is used to predict the occurrence of chatter vibrations, and to investigate the effects of various machining parameters on this phenomenon. The dynamic properties of the machine tool at the tool tip are obtained based on experimental modal analysis, and are used in the model as the cutter dynamics. The model allows for the natural development of vibration as the result of the chiptool engagement, and accounts for various phenomena that occur at the chip-tool interface ultimately leading to stable or unstable cutting. The model was used to demonstrate the effects of the machining parameters, such as the axial depth of cut, radial immersion, and feed rate, on the occurrence of chatter. Additionally, the phenomenon of jumping out of the cut region could be observed in this model and its effect on the chatter process is demonstrated. The numerical model is verified based on comparisons with experimental results.

The full text can be downloaded at https://link.springer.com/content/pdf/10.1007%2Fs40436-018-0228-7.pdf

Key words: Machining chatter, Milling, Finite element model (FEM) simulation, Feed rate

Ehsan Jafarzadeh, Mohammad R. Movahhedy, Saeed Khodaygan, Mohammad Ghorbani. Prediction of machining chatter in milling based on dynamic FEM simulations of chip formation[J]. Advances in Manufacturing, 2018, 6(3): 334-344.

TrendMD

Add to citation manager EndNote|Reference Manager|ProCite|BibTeX|RefWorks

URL: https://www.aim.shu.edu.cn/EN/10.1007/s40436-018-0228-7

https://www.aim.shu.edu.cn/EN/Y2018/V6/I3/334

References

1. Tobias S, Fishwick W (1958) The chatter of lathe tools under orthogonal cutting conditions. Trans ASME 80(2):1079-1088
2. Tlusty J, Polacek M (1963) The stability of machine tools against self-excited vibrations in machining. Int Res Prod Eng 1(1):465-474
3. Merritt HE (1965) Theory of self-excited machine-tool chatter:contribution to machine-tool chatter research. J Manuf Sci Eng 87(4):447-454
4. Sridhar R, Hohn R, Long G (1968) A general formulation of the milling process equation:contribution to machine tool chatter research 5. J Manuf Sci Eng 90(2):317-324
5. Hanna N, Tobias S (1974) A theory of nonlinear regenerative chatter. J Manuf Sci Eng 96(1):247-255
6. Wang Y, Wang T, Yu Z et al (2015) Chatter prediction for variable pitch and variable helix milling. Shock Vib. https://doi.org/10.1155/2015/419172
7. Moradi H, Bakhtiari-Nejad F, Movahhedy MR et al (2010) Nonlinear behaviour of the regenerative chatter in turning process with a worn tool:forced oscillation and stability analysis. Mech Mach Theory 45(8):1050-1066
8. Tlusty J, Zaton W, Ismail F (1983) Stability lobes in milling. CIRP Ann Manuf Technol 32(1):309-313
9. Mahnama M, Movahhedy M (2010) Prediction of machining chatter based on FEM simulation of chip formation under dynamic conditions. Int J Mach Tools Manuf 50(7):611-620
10. Mahnama M, Movahhedy MR (2012) Application of FEM simulation of chip formation to stability analysis in orthogonal cutting process. J Manuf Process 14(3):188-194
11. Moufki A, Devillez A, Segreti M et al (2006) A semi-analytical model of non-linear vibrations in orthogonal cutting and experimental validation. Int J Mach Tools Manuf 46(3-4):436-449
12. Hajmohammadi MS, Movahhedy MR, Moradi H (2014) Investigation of thermal effects on machining chatter based on FEM simulation of chip formation. CIRP J Manuf Sci Technol 7(1):1-10
13. Jafarzadeh E, Movahhedy MR (2017) Numerical simulation of interaction of mode-coupling and regenerative chatter in machining. J Manuf Process 27:252-260
14. Tlusty J, Andrews G (1983) A critical review of sensors for unmanned machining. CIRP Ann Manuf Technol 32(2):563-572
15. Association A (2000) Aluminum standards and data. Aluminum Association, Arlington
16. Brar N, Joshi V, Harris B (2009) Constitutive model constants for Al7075-T651 and Al7075-T6. Proc Am Phys Soc Top Group Shock Compres Condens Matter 1195(1):945-948
17. Bolar G, Joshi S (2014) Three dimensional finite element modeling and simulation of curvilinear thin-wall machining of aluminum 7075-T6 alloy. Processing and fabrication of advanced materials, World Scientific Publishing, Singapore
18. Tlusty J (2000) Manufacturing processes and equipment. Prentice Hall, Englewood
19. Insperger T, Stépán G (2004) Updated semi-discretization method for periodic delay-differential equations with discrete delay. Int J Numer Methods Eng 6(1):117-141

[1]	Jun-Cheng Lu, Jian Wang, Qiang Gao, Qian Zheng, Yi-Fan Lu, Ya-Ou Zhang, Wan-Sheng Zhao. Investigation into material removal mechanism of high-volume-fraction SiCp/Al composite by fast ED milling [J]. Advances in Manufacturing, 2026, 14(2): 397-415.
[2]	Guan-Yan Ge, Yu-Kun Xiao, Jun Lv, Zheng-Chun Du. Mechanism analysis and suppression for chatter and surface location error induced by error compensation [J]. Advances in Manufacturing, 2025, 13(4): 750-767.
[3]	Bo-Wen Song, Da-Wei Zhang, Xiu-Bing Jing, Ying-Ying Ren, Yun Chen, Huai-Zhong Li. Enhanced cutting force model in micro-milling incorporating material separation criterion [J]. Advances in Manufacturing, 2025, 13(4): 813-830.
[4]	Mohammad Pasandidehpoor, Ana Rita Nogueira, Jo?o Mendes-Moreira, Ricardo Sousa. Survey on machine learning applied to CNC milling processes [J]. Advances in Manufacturing, 2025, 13(4): 847-885.
[5]	Zhen-Jing Duan, Shuai-Shuai Wang, Shu-Yan Shi, Ji-Yu Liu, Yu-Heng Li, Zi-Heng Wang, Chang-He Li, Yu-Yang Zhou, Jin-Long Song, Xin Liu. Surface quality evaluation of cold plasma and NMQL multi-field coupling eco-friendly micro-milling 7075-T6 aluminum alloy [J]. Advances in Manufacturing, 2025, 13(1): 69-87.
[6]	Jin Zhang, Li Ling, Qian-Yue Wang, Xue-Feng Huang, Xin-Zhen Kang, Gui-Bao Tao, Hua-Jun Cao. Surface quality investigation in high-speed dry milling of Ti-6Al-4V by using 2D ultrasonic-vibration-assisted milling platform [J]. Advances in Manufacturing, 2024, 12(2): 349-364.
[7]	Shailendra Chauhan, Rajeev Trehan, Ravi Pratap Singh. State of the art in finite element approaches for milling process: a review [J]. Advances in Manufacturing, 2023, 11(4): 708-751.
[8]	Zheng Zhou, Chang-Feng Yao, Liang Tan, Ya Zhang, Yi Fan. Experimental study on surface integrity refactoring changes of Ti-17 under milling-ultrasonic rolling composite process [J]. Advances in Manufacturing, 2023, 11(3): 492-508.
[9]	Lorcan O'Toole, Feng-Zhou Fang. Optimal tool design in micro-milling of difficult-to-machine materials [J]. Advances in Manufacturing, 2023, 11(2): 222-247.
[10]	Vitor F. C. Sousa, Francisco J. G. Silva, Ricardo Alexandre, José S. Fecheira, Gustavo Pinto, Andresa Baptista. Experimental study on the wear evolution of different PVD coated tools under milling operations of LDX2101 duplex stainless steel [J]. Advances in Manufacturing, 2023, 11(1): 158-179.
[11]	Bao-Yu Zhang, Yu-Ning Zeng, Xue-Qin Pang, Song-Qing Li, Xiao Liu, Wen-Jun Deng. Feasibility analysis and process characteristics of selective laser ablation assisted milling Inconel 718 [J]. Advances in Manufacturing, 2022, 10(4): 495-519.
[12]	Miao-Xian Guo, Jin Liu, Li-Mei Pan, Chong-Jun Wu, Xiao-Hui Jiang, Wei-Cheng Guo. An integrated machine-process-controller model to predict milling surface topography considering vibration suppression [J]. Advances in Manufacturing, 2022, 10(3): 443-458.
[13]	Da-Xiang Deng, Jian Zheng, Xiao-Long Chen, Guang Pi, Yong-Heng Liu. Fabrication of micro pin fins on inclined V-shaped microchannel walls via laser micromilling [J]. Advances in Manufacturing, 2022, 10(2): 220-234.
[14]	Lorcan O'Toole, Cheng-Wei Kang, Feng-Zhou Fang. Precision micro-milling process: state of the art [J]. Advances in Manufacturing, 2021, 9(2): 173-205.
[15]	Dong-Dong Li, Wei-Min Zhang, Yuan-Shi Li, Feng Xue, Jürgen Fleischer. Chatter identifi cation of thin-walled parts for intelligent manufacturing based on multi-signal processing [J]. Advances in Manufacturing, 2021, 9(1): 22-33.