Effect of build and unit cell orientation on the tensile, compressive, and torsional behavior of Ti-6Al-4V gyroid sheet-based structures

doi:10.1007/s40436-025-00566-9

Abstract

Abstract: Laser powder bed fusion (LPBF) enables the fabrication of intricate porous metallic structures, such as the sheet-based gyroid, recently used in orthopedic implants. Many implants are subjected to a complex stress environment, making strength verification across different loading modes imperative. This study investigates the effect of both unit cell and build orientation on gyroid structures. Build orientation and unit cell orientation were varied from 0° to 90° in 15° increments to determine the degree of anisotropy of Ti-6Al-4V samples in tension, compression, and torsion. For the relatively isotropic gyroid structure, build orientation was the most influential factor on anisotropy in tension and compression. The samples with 30° build orientation (B30) showed the highest strength across all three loading modes due to the overall print quality and orientation of layers withstanding the applied forces. These results guide the design optimization of 3D printed orthopedic implants with varying build and unit cell orientation.

The full text can be downloaded at https://doi.org/10.1007/s40436-025-00566-9

Key words: 3D printing, Laser power bed fusion (LPBF), Titanium alloys, Gyroid, Anisotropy

Gaetano Pollara, Amanda Heimbrook, Livan Fratini, Ken Gall. Effect of build and unit cell orientation on the tensile, compressive, and torsional behavior of Ti-6Al-4V gyroid sheet-based structures[J]. Advances in Manufacturing, 2026, 14(2): 259-273.

TrendMD

References

[1] Pan L, Zhang CL, Wang L et al (2020) Molten pool structure, temperature and velocity flow in selective laser melting AlCu5MnCdVA alloy. Mater Res Express 7:086516. https://doi.org/10.1088/2053-1591/abadcf
[2] Liu Y, Wang W, Zhang LC (2017) Additive manufacturing techniques and their biomedical applications. Family Med Commun Health 5(4):286-298
[3] Ngo TD, Kashani A, Imbalzano G et al (2018) Additive manufacturing (3D printing): a review of materials, methods, applications and challenges. Compos B Eng 143:172-196. https://doi.org/10.1016/j.compositesb.2018.02.012
[4] Elshalakany AB, Abdel-Mottaleb MM, Salunkhe S et al (2023) Mechanical properties of titanium alloys additive manufacturing for biomedical applications. In: Salunkhe S et al (eds) Advances in metal additive manufacturing, Woodhead Publishing, Cambridge, UK, pp 219-231. https://doi.org/10.1016/B978-0-323-91230-3.00007-X
[5] Bai Y, Zhao C, Wang D et al (2022) Evolution mechanism of surface morphology and internal hole defect of 18Ni300 maraging steel fabricated by selective laser melting. J Mater Process Technol 299:117328. https://doi.org/10.1016/j.jmatprotec.2021.117328
[6] Sing SL, An J, Yeong WY et al (2016) Laser and electron-beam powder-bed additive manufacturing of metallic implants: a review on processes, materials and designs. J Orthop Res 34:369-385. https://doi.org/10.1002/jor.23075
[7] Buffa G, Palmeri D, Pollara G et al (2024) Process parameters and surface treatment effects on the mechanical and corrosion resistance properties of Ti6Al4V components produced by laser powder bed fusion. Prog Addit Manuf 9:151-167. https://doi.org/10.1007/s40964-023-00440-9
[8] Sun QD, Sun J, Guo K et al (2022) Influences of processing parameters and heat treatment on microstructure and mechanical behavior of Ti-6Al-4V fabricated using selective laser melting. Adv Manuf 10:520-540. https://doi.org/10.1007/s40436-022-00389-y
[9] Ridzwan M, Shuib S, Hassan AY et al (2007) Problem of stress shielding and improvement to the hip implant designs: a review. J Med Sci 7:460-467. https://doi.org/10.3923/jms.2007.460.467
[10] Niinomi M, Nakai M (2011) Titanium-based biomaterials for preventing stress shielding between implant devices and bone. Int J Biomater 2011:836587. https://doi.org/10.1155/2011/836587
[11] Al-Tamimi AA, Peach C, Fernandes PR et al (2017) Topology optimization to reduce the stress shielding effect for orthopedic applications. Proc CIRP 65:202-206. https://doi.org/10.1016/j.procir.2017.04.032
[12] Wang C, Huang W, Zhou Y et al (2020) 3D printing of bone tissue engineering scaffolds. Bioact Mater 5:82-91. https://doi.org/10.1016/j.bioactmat.2020.01.004
[13] Zhang B, Pei X, Zhou C et al (2018) The biomimetic design and 3D printing of customized mechanical properties porous Ti6Al4V scaffold for load-bearing bone reconstruction. Mater Des 152:30-39. https://doi.org/10.1016/j.matdes.2018.04.065
[14] Wang H, Su K, Su L et al (2018) The effect of 3D-printed Ti6Al4V scaffolds with various macropore structures on osteointegration and osteogenesis: a biomechanical evaluation. J Mech Behav Biomed Mater 88:488-496. https://doi.org/10.1016/j.jmbbm.2018.08.049
[15] King WE, Anderson AT, Ferencz RM et al (2015) Laser powder bed fusion additive manufacturing of metals; physics, computational, and materials challenges. Appl Phys Rev 2:041304. https://doi.org/10.1063/1.4937809
[16] Riva L, Ginestra PS, Ceretti E (2021) Mechanical characterization and properties of laser-based powder bed-fused lattice structures: a review. Int J Adv Manuf Technol 113:649-671
[17] Aufa AN, Hassan MZ, Ismail Z (2022) Recent advances in Ti-6Al-4V additively manufactured by selective laser melting for biomedical implants: prospect development. J Alloys Compd 896:163072. https://doi.org/10.1016/j.jallcom.2021.163072
[18] Al-Ketan O, Rowshan R, Abu Al-Rub RK (2018) Topology-mechanical property relationship of 3D printed strut, skeletal, and sheet based periodic metallic cellular materials. Addit Manuf 19:167-183. https://doi.org/10.1016/j.addma.2017.12.006
[19] Yuan L, Ding S, Wen C (2019) Additive manufacturing technology for porous metal implant applications and triple minimal surface structures: a review. Bioact Mater 4:56-70. https://doi.org/10.1016/j.bioactmat.2018.12.003
[20] Yan C, Hao L, Hussein A et al (2015) Ti-6Al-4V triply periodic minimal surface structures for bone implants fabricated via selective laser melting. J Mech Behav Biomed Mater 51:61-73. https://doi.org/10.1016/j.jmbbm.2015.06.024
[21] Yang E, Leary M, Lozanovski B et al (2019) Effect of geometry on the mechanical properties of Ti-6Al-4V gyroid structures fabricated via SLM: a numerical study. Mater Des 184:108165. https://doi.org/10.1016/j.matdes.2019.108165
[22] Bobbert FSL, Lietaert K, Eftekhari AA et al (2017) Additively manufactured metallic porous biomaterials based on minimal surfaces: a unique combination of topological, mechanical, and mass transport properties. Acta Biomater 53:572-584. https://doi.org/10.1016/j.actbio.2017.02.024
[23] Zhang XY, Yan XC, Fang G et al (2020) Biomechanical influence of structural variation strategies on functionally graded scaffolds constructed with triply periodic minimal surface. Addit Manuf 32:101015. https://doi.org/10.1016/j.addma.2019.101015
[24] Mathey E, Pelletier MH, Walsh WR et al (2024) Implant strength contributes to the osseointegration strength of porous metallic materials. J Biomech Eng 146:101005. https://doi.org/10.1115/1.4065405
[25] Luo W, Wang Y, Wang Z et al (2024) Advanced topology of triply periodic minimal surface structure for osteogenic improvement within orthopedic metallic screw. Mater Today Bio 27:101118. https://doi.org/10.1016/j.mtbio.2024.101118
[26] Salaha ZFM, Ammarullah MI, Abdullah NNAA et al (2023) Biomechanical effects of the porous structure of gyroid and voronoi hip implants: a finite element analysis using an experimentally validated model. Materials 16:3298. https://doi.org/10.3390/ma16093298
[27] Kladovasilakis N, Tsongas K, Tzetzis D (2020) Finite element analysis of orthopedic hip implant with functionally graded bioinspired lattice structures. Biomimetics 5:44. https://doi.org/10.3390/biomimetics5030044
[28] Nelson K, Kelly CN, Gall K (2022) Effect of stress state on the mechanical behavior of 3D printed porous Ti6Al4V scaffolds produced by laser powder bed fusion. Mater Sci Eng B Solid State Mater Adv Technol 286:116013. https://doi.org/10.1016/j.mseb.2022.116013
[29] Zaharin HA, Rani AMA, Azam FI et al (2018) Effect of unit cell type and pore size on porosity and mechanical behavior of additively manufactured Ti6Al4V scaffolds. Materials 11:2402. https://doi.org/10.3390/ma11122402
[30] Kelly CN, Kahra C, Maier HJ et al (2021) Processing, structure, and properties of additively manufactured titanium scaffolds with gyroid-sheet architecture. Addit Manuf 41:101916. https://doi.org/10.1016/j.addma.2021.101916
[31] Soro N, Saintier N, Merzeau J et al (2021) Quasi-static and fatigue properties of graded Ti-6Al-4V lattices produced by laser powder bed fusion (LPBF). Addit Manuf 37:101653. https://doi.org/10.1016/j.addma.2020.101653
[32] Wauthle R, Vrancken B, Beynaerts B et al (2015) Effects of build orientation and heat treatment on the microstructure and mechanical properties of selective laser melted Ti6Al4V lattice structures. Addit Manuf 5:77-84. https://doi.org/10.1016/j.addma.2014.12.008
[33] Palmeri D, Buffa G, Pollara G et al (2021) The effect of building direction on microstructure and microhardness during selective laser melting of Ti6Al4V titanium alloy. J Mater Eng Perform 30:8725-8734. https://doi.org/10.1007/s11665-021-06039-x
[34] Barber H, Kelly CN, Nelson K et al (2021) Compressive anisotropy of sheet and strut based porous Ti-6Al-4V scaffolds. J Mech Behav Biomed Mater 115:104243. https://doi.org/10.1016/j.jmbbm.2020.104243
[35] Palmeri D, Buffa G, Pollara G et al (2022) Sample building orientation effect on porosity and mechanical properties in selective laser melting of Ti6Al4V titanium alloy. Mater Sci Eng A 830:142306. https://doi.org/10.1016/j.msea.2021.142306
[36] Cheal EJ, Spector M, Hayes WC (1992) Role of loads and prosthesis material properties on the mechanics of the proximal femur after total hip arthroplasty. J Orthop Res 10:405-422. https://doi.org/10.1002/jor.1100100314
[37] Nelson K (2022) Evaluation of stress state on the mechanical properties of 3D printed metallic lattice structures fabricated via laser powder bed fusion for orthopedic applications. Dissertation, Duke University
[38] Pham A, Kelly C, Gall K (2020) Free boundary effects and representative volume elements in 3D printed Ti-6Al-4V gyroid structures. J Mater Res 35:2547-2555. https://doi.org/10.1557/jmr.2020.105
[39] Kelly CN, Francovich J, Julmi S et al (2019) Fatigue behavior of as-built selective laser melted titanium scaffolds with sheet-based gyroid microarchitecture for bone tissue engineering. Acta Biomater 94:610-626. https://doi.org/10.1016/j.actbio.2019.05.046
[40] Emanuelli L, Jam A, du Plessis A et al (2023) Manufacturability of functionally graded porous β-Ti21S auxetic architected biomaterials produced by laser powder bed fusion: comparison between 2D and 3D metrological characterization. Int J Bioprint 9:728. https://doi.org/10.18063/ijb.728
[41] Chua C, Sing SL, Chua CK (2023) Characterisation of in-situ alloyed titanium-tantalum lattice structures by laser powder bed fusion using finite element analysis. Virtual Phys Prototyp. https://doi.org/10.1080/17452759.2022.2138463
[42] Huang S, Sing SL, de Looze G et al (2020) Laser powder bed fusion of titanium-tantalum alloys: compositions and designs for biomedical applications. J Mech Behav Biomed Mater 108:103775. https://doi.org/10.1016/j.jmbbm.2020.103775
[43] Karami K, Blok A, Weber L et al (2020) Continuous and pulsed selective laser melting of Ti6Al4V lattice structures: effect of post-processing on microstructural anisotropy and fatigue behaviour. Addit Manuf 36:101433. https://doi.org/10.1016/j.addma.2020.101433
[44] Vallejos JM, Barriobero-Vila P, Gussone J et al (2021) In situ high-energy synchrotron X-Ray diffraction reveals the role of texture on the activation of slip and twinning during deformation of laser powder bed fusion Ti-6Al-4V. Adv Eng Mater 23:10-14. https://doi.org/10.1002/adem.202001556
[45] Fousova M, Vojtech D (2017) Influence of process conditions on additive manufacture of Ti6Al4V alloy by SLM technology. Manuf Technol 17:17-18. https://doi.org/10.21062/ujep/x.2017/a/1213-2489/MT/17/5/696
[46] Yadroitsev I, Krakhmalev P, Yadroitsava I et al (2018) Qualification of Ti6Al4V ELI alloy produced by laser powder bed fusion for biomedical applications. JOM 70:372-377. https://doi.org/10.1007/s11837-017-2655-5
[47] Gangireddy S, Faierson EJ, Mishra RS (2018) Influences of post-processing, location, orientation, and induced porosity on the dynamic compression behavior of Ti-6Al-4V alloy built through additive manufacturing. J Dyn Behav Mater 4:441-451. https://doi.org/10.1007/s40870-018-0157-3