Modeling and simulation of percussive impact for robotic riveting system

doi:10.1007/s40436-014-0091-0

Abstract

Abstract: Riveting is one of the major joining methods used in assembly, and the robotic riveting has been gradually introduced into aircraft industry. In this paper, a method is presented for modeling and simulation of percussive robotic riveting. In percussive riveting, vibration always exists. When an impact force is employed, a forced vibration will be induced. If it resonates with a robot natural frequency, the vibration will cause damage to the robot. The main content of this paper is divided into three parts. Firstly, a robot dynamic model is established to compute the driving torque for each joint. Secondly, vibration responses under impact are analyzed for the percussive riveting process. Thirdly, the effect of riveting on robot vibration is studied over the robot workspace. The purpose of this paper is to discuss the suitable regions for riveting where the robot vibration is very minimal. It is shown that based on the presented method an appropriate trajectory can be planned for robotic riveting.

Key words: Robotic dynamics , Analysis , Vibration response, Impact force , Riveting

Shuai Guo,Song-Liang Nie, Feng-Feng Xi,Tao Song. Modeling and simulation of percussive impact for robotic riveting system[J]. Advances in Manufacturing, 2014, 2(4): 344-352.

TrendMD

Add to citation manager EndNote|Reference Manager|ProCite|BibTeX|RefWorks

URL: https://www.aim.shu.edu.cn/EN/10.1007/s40436-014-0091-0

https://www.aim.shu.edu.cn/EN/Y2014/V2/I4/344

References

1. Li YW, Xi FF, Behdinan K (2010) Dynamic modeling and simulation of percussive impact riveting for robotic automation. J Comput Nonlinear Dyn 5(2):021011
2. Qu W, Dong H, Ke Y (2011) Pose accuracy compensation technology in robot-aided aircraft assembly drilling process. Acta Aeronautica et Astronautica Sinica 32(10):1951–1960
3. Xiao H, Li Y, Zhang KF et al (2010) Multi-objective optimization method for automatic drilling and riveting sequence planning. Chin J Aeronaut 23(6):734–742
4. Bi S, Liang J (2011) Robotic drilling system for titanium structures. Int J Adv Manuf Technol 54(5/8):767–774
5. Olsson T, Robertsson A, Johansson R (2007) Flexible force control for accurate low-cost robot drilling. In: 2007 IEEE
international conference on robotics and automation, Roma, Italy,10–14 April 2007
6. Dhanaraj C, Sharan M (1995) Efficient modeling of rigid link robot dynamic problems with friction. Mech Mach Theory 30(5):749–764
7. Zhao Y, Bai Z (2010) Dynamics analysis of space robot manipulator with joint clearance. Acta Astronautica 68(7):1147–1155
8. KalyoncuM(2007) Mathematical modelling and dynamic response of a multi-straight-line path tracing flexible robot manipulator with rotating-prismatic joint. Appl Math Model 32(6):1087–1098
9. Shi ZX, Fung Eric HK, Li YC (1999) Dynamic modelling of a rigid-flexible manipulator for constrained motion task control. Appl Math Model 23(7):509–525
10. Knani J (2002) Dynamic modeling of flexible robotic mechanisms and adaptive robust control of trajectory computer simulation. Appl Math Model 26(12):1113–1124
11. Zhang C, Yu Y (2003) Dynamic modeling of robot arm with joint flexibility and link flexibility manipulating a constrained object. Chin J Mech Eng 39(6):9–12
12. Lee CSG, Lee BH, Nigam R (1982) An efficient formulation of robot arm dynamics for control analysis and manipulator design. Technical Reports of Robotics and Integrated Manufacturing, University of Michigan, Ann Arbor, Michigan
13. Boscariol P, Gasparetto A (2013) Model-based trajectory planning for flexible-link mechanisms with bounded jerk. Robot Comput Integr Manuf 8(29):90–99
14. Yin HB, Kobayashi Y, Hoshino Y et al (2011) Modeling and vibration analysis of flexible robotic arm under fast motion in consideration of nonlinearity. J Syst Des Dyn 5(5):909–924
15. XieX,Huang J, LiangZ(2013) Vibration reduction forflexible systems by command smoothing. Mech Syst Signal Process 8(39):461–470
16. Wang Y, Huang QB, Zhou MG et al (2006) Vibration response analysis of 2-DOF locally nonlinear systems based on the theory of modal super position. J Chongqing Univ (English Edition) 5(3):125–130

[1]	Jin-Rui Duan, Chao Chen. Mechanical properties and failure mechanisms of self-piercing riveted aluminum alloys with different edge distances [J]. Advances in Manufacturing, 2025, 13(3): 655-667.
[2]	Muhammad Sajjad, Javier Trinidad, Gorka Plata, Jokin Lozares, Joseba Mendiguren. Sensitivity analysis of near solidus forming (NSF) process with digital twin using Taguchi approach [J]. Advances in Manufacturing, 2025, 13(2): 322-336.
[3]	Yan-Hua Bian, Chong-Xin Tian, Bo Chen, Bin-Xin Dong, Shao-Xia Li, Zhi-Yong Li, Yang-Rui Nan, Xiu-Li He, Gang Yu. Single-track geometrical characteristics under different energy input and mass addition in coaxial laser cladding [J]. Advances in Manufacturing, 2024, 12(4): 742-763.
[4]	Yu-Xiang Ji, Li Huang, Qiu-Ren Chen, Charles K. S. Moy, Jing-Yi Zhang, Xiao-Ya Hu, Jian Wang, Guo-Bi Tan, Qing Liu. A machine learning-based calibration method for strength simulation of self-piercing riveted joints [J]. Advances in Manufacturing, 2024, 12(3): 465-483.
[5]	Chen-Di Wei, Qiu-Ren Chen, Min Chen, Li Huang, Zhong-Jie Yue, Si-Geng Li, Jian Wang, Li Chen, Chao Tong, Qing Liu. Predicting fatigue life of automotive adhesive bonded joints: a data-driven approach using combined experimental and numerical datasets [J]. Advances in Manufacturing, 2024, 12(3): 522-537.
[6]	Bao-Ri Zhang, Yong-Hua Shi. A novel weld-pool-length monitoring method based on pixel analysis in plasma arc additive manufacturing [J]. Advances in Manufacturing, 2024, 12(2): 335-348.
[7]	Lin Ling, Zhe-Ming Song, Xi Zhang, Peng-Zhou Cao, Xiao-Qiao Wang, Cong-Hu Liu, Ming-Zhou Liu. Manufacturing task data chain-driven production logistics trajectory analysis and optimization decision making method [J]. Advances in Manufacturing, 2024, 12(1): 185-206.
[8]	Yan Liu, Qiu Tang, Xin-Cheng Tian, Long Cui. Flexible servo riveting system control strategy based on the RBF network and self-pierce riveting process [J]. Advances in Manufacturing, 2023, 11(1): 39-55.
[9]	Chang-Yong Yang, Zhi Wang, Hao Su, Yu-Can Fu, Nian-Hui Zhang, Wen-Feng Ding. Numerical analysis and experimental validation of surface roughness and morphology in honing of Inconel 718 nickel-based superalloy [J]. Advances in Manufacturing, 2023, 11(1): 130-142.
[10]	Long-Xu Yao, Zhan-Qiang Liu, Qing-Hua Song, Bing Wang, Yu-Kui Cai. Effects of process parameters on periodic impact force exerting on cutting tool in ultrasonic vibration-assisted oblique turning [J]. Advances in Manufacturing, 2022, 10(3): 411-427.
[11]	Ekrem Oezkaya, Sebastian Michel, Dirk Biermann. Experimental and computational analysis of the coolant distribution considering the viscosity of the cutting fluid during machining with helical deep hole drills [J]. Advances in Manufacturing, 2022, 10(2): 235-249.
[12]	E. Virgillito, A. Aversa, F. Calignano, M. Lombardi, D. Manfredi, D. Ugues, P. Fino. Failure mode analysis on compression of lattice structures with internal cooling channels produced by laser powder bed fusion [J]. Advances in Manufacturing, 2021, 9(3): 403-413.
[13]	Yun-Yun Pi, Wen-Jun Deng, Jia-Yang Zhang, Xiao-Long Yin, Wei Xia. Towards understanding the microstructure and temperature rule in large strain extrusion machining [J]. Advances in Manufacturing, 2021, 9(2): 262-272.
[14]	Carmita Camposeco-Negrete. Analysis and optimization of sustainable machining of AISI O1 tool steel by the wire-EDM process [J]. Advances in Manufacturing, 2021, 9(2): 304-317.
[15]	Omar Ahmed Mohamed, Syed Hasan Masood, Jahar Lal Bhowmik. Modeling, analysis, and optimization of dimensional accuracy of FDM-fabricated parts using defi nitive screening design and deep learning feedforward artifi cial neural network [J]. Advances in Manufacturing, 2021, 9(1): 115-129.