High speed steel produced by spray forming

doi:10.1007/s40436-016-0137-6

Abstract

Abstract:

In this paper, ASP2030 (A30) high speed steel (HSS) was produced by spray forming and the microstructure was studied by optical microscopy (OM), scanning electron microscopy (SEM), transmission electron microscopy (TEM), electron probe microanalysis (EPMA) and X-ray diffraction (XRD). The spray formed A30 (SF A30) steel exhibited a very uniform and fine microstructure consisting of martensite, retained austenite and uniformly distributed network carbides. Microstructure refining can be explained in terms of the rapid solidification of spray forming. M₂C, MC and M₆C type carbides were found in the as-sprayed A30 HSS by XRD and TEM. A uniform distribution of carbides was obtained after forging and annealing. The microstructure properties of SF A30 steel indicate that spray forming can be considered as a cost-effective route for the production of A30 steels and other highly alloyed steels.

Key words: Spray forming, High speed steel (HSS), Microstructure, Carbides, Property

Shun-Li Zhao, Jun-Fei Fan, Jie-Yu Zhang, Kuo-Chih Chou, Hai-Rong Le. High speed steel produced by spray forming[J]. Advances in Manufacturing, 2016, 4(2): 115-122.

TrendMD

References

1. Moon HK, Lee KB, Kwon H (2008) Influences of Co addition and austenitizing temperature on secondary hardening and impact fracture behavior in P/M high speed steels of W-Mo-Cr-V(-Co) system. Mater Sci Eng A 474:328-334
2. Mesquita RA, Barbosa CA (2004) Spray forming high speed steel-properties and processing. Mater Sci Eng A 383:87-95
3. Zhou B, Shen Y, Chen J, Cui ZS (2011) Breakdown behavior of eutectic carbides in high speed steel during hot compression. J Iron Steel Res Int 18:41-48
4. Hetzner DW (2001) Refining carbide size distributions in M1 high speed steel by processing and alloying. Mater Charact 46:175-182
5. Wronski AS, Wright CS, Bolton JD, Bienvenu Y, Jeandin M, Smith AB (1991) PM HSS for aerospace automotive and cutting tool applications. Met Powder Rep 46(50-51):53-55
6. Grant PS (1995) Spray forming. Prog Mater Sci 39:497-545
7. Rodenburg C, Krzyzanowski M, Beynon JH, Rainforth WM (2004) Hot workability of spray-formed AISI M3:2 high-speed steel. Mater Sci Eng A 386:420-427
8. Schulz A, Uhlenwinkel V, Escher C, Kohlmann R, Kulmburg A, Montero MC, Rabitsch R, Schützenhöfer W, Stocchi D, Viale D (2008) Opportunities and challenges of spray forming high-alloyed steels. Mater Sci Eng A 477:69-79
9. Bhargava AK, Tiwari AN (1992) Effect of rapid solidification and heat treatment on D2 steel. Int J Rapid Solidif 7:51-66
10. Zhang JG (2003) Research in spray forming technology and its applications in metallurgy. J Mater Process Technol 138:357-360
11. Zhang JG, Xu HB, Shi HS, Wu JS, Sun DS (2003) Microstructure and properties of spray formed Cr₁₂MoV steel for rolls. J Mater Process Technol 111:79-84
12. Ikawa Y, Itami T, Kumagai K, Kawashima Y, Leatham AG, Coombs JS (1990) Spray deposition method and its application to the production of mill rolls. ISIJ Int 30:756-763
13. Lee ES, Park WJ, Baik KH, Ahn S (1998) Different carbide types and their effect on bend properties of a spray-formed high speed steel. Scr Mater 39:1133-1138
14. Zhang Y, Zhang GQ, Li Z, Li ZD, Yuan H, Xu WY, Liu N, Tian SF (2007) Analysis of twin-nozzle-scanning spray forming process and spray formed high speed steel (HSS). J Iron Steel Res Int 14:7-10
15. Yan F, Xu Z, Shi HS, Fan JF (2008) Microstructure of the spray formed Vanadis 4 steel and its ultrafine structure. Mater Charact 59:592-597
16. Cui CS, Fritsching U, Schulz A, Tinscher R, Bauckhage K, Mayr P (2005) Spray forming of homogeneous 100Cr6 bearing steel billets. J Mater Process Technol 168:496-504
17. Yu FX, Cui JZ, Ranganathan S, Dwarakadasa ES (2001) Fundamental differences between spray forming and other semisolid processes. Mater Sci Eng A 304-306:621-626
18. Wei SZ, Zhu JH, Xu LJ (2005) Research on wear resistance of high speed steel with high vanadium content. Mater Sci Eng A 404:138-145
19. Zhou H, Wang JG, Jia SS, Keisaku OGI (1997) Solidified microstructures and phases of high speed steels containing different V and C content. Acta Metall Sin 33:838-843
20. Luan YK, Song NN, Bai YL, Kang XH, Li DZ (2010) Effect of solidification rate on the morphology and distribution of eutectic carbides in centrifugal casting high-speed steel rolls. J Mater Process Technol 210:536-541
21. Lee ES, Park WJ, Jung JY (1998) Solidification microstructure and M₂C carbide decomposition in a spray-formed high-speed steel. Metall Mater Trans 29A:1395-1404
22. Xu Q, Lavernia EJ (1999) Microstructure evolution during the initial stages of spray atomization and deposition. Scr Mater 41:535-540
23. Pan FS, Wang WQ, Tang AT (2011) Phase transformation refinement of coarse primary carbides in M2 high speed steel. Prog Nat Sci 21:180-186
24. Ve?ko Pirtovšek T, Kugler G, Godec M, Ter?elj M (2011) Microstructural characterization during the hot deformation of 1.17C-11.3Cr-1.48V-2.24W-1.35Mo ledeburitic tool steel. Mater Charact 62:189-197
25. Meurling F, Melander A, Tidesten M, Westin L (2001) Influence of carbide and inclusion contents on the fatigue properties of high speed steels and tool steels. Int J Fatigue 23:215-224

[1]	Parveen Kumar, Satish Kumar Sharma, Ratnesh Kumar Raj Singh. Effect of cooling media on bead geometry, microstructure, and mechanical properties of wire arc additive manufactured IN718 alloy [J]. Advances in Manufacturing, 2024, 12(1): 124-149.
[2]	Xue-hong Shen, Chang-Feng Yao, Liang Tan, Ding-Hua Zhang. Prediction model of surface integrity characteristics in ball end milling TC17 titanium alloy [J]. Advances in Manufacturing, 2023, 11(3): 541-565.
[3]	Yan-Hua Bian, Gang Yu, Xin Zhao, Shao-Xia Li, Xiu-Li He, Chong-Xin Tian, Zhi-Yong Li. Exit morphology and mechanical property of FDM printed PLA: influence of hot melt extrusion process [J]. Advances in Manufacturing, 2023, 11(1): 56-74.
[4]	Qi-Dong Sun, Jie Sun, Kai Guo, Saad Waqar, Jiang-Wei Liu, Lei-Shuo Wang. Influences of processing parameters and heat treatment on microstructure and mechanical behavior of Ti-6Al-4V fabricated using selective laser melting [J]. Advances in Manufacturing, 2022, 10(4): 520-540.
[5]	Bao-Cai Zhang, Shi-Fei Chen, Nasim Khiabani, Yu Qiao, Xin-Chang Wang. Research on the underlying mechanism behind abrasive flow machining on micro-slit structures and simulation of viscoelastic media [J]. Advances in Manufacturing, 2022, 10(3): 382-396.
[6]	Kai Ding, Yuan-Heng Zhang, Shang-Fei Qiao, Guan-Zhi Wu, Tao Wei, Xia Liu, Yu-Lai Gao. Formation of the anomalous microstructure in the weld metal of Co-based alloy/AISI 410 stainless steel dissimilar welded joint [J]. Advances in Manufacturing, 2022, 10(2): 250-259.
[7]	Yong-Cheng Lin, Jiang-Shan Zhu, Jia-Yang Chen, Jun-Quan Wang. Residual-stress relaxation mechanism and model description of 5052H32 Al alloy spun ellipsoidal heads during annealing treatment [J]. Advances in Manufacturing, 2022, 10(1): 87-100.
[8]	Omar Ahmed Mohamed, Syed Hasan Masood, Wei Xu. Nickel-titanium shape memory alloys made by selective laser melting:a review on process optimisation [J]. Advances in Manufacturing, 2022, 10(1): 24-58.
[9]	Jia-Yang Chen, Yong-Cheng Lin, Guo-Dong Pang, Xin-He Li. Effects of spinning parameters on microstructures of ellipsoidal heads during marginal-restraint mandrel-free spinning [J]. Advances in Manufacturing, 2020, 8(4): 457-472.
[10]	Behrouz Bagheri, Mahmoud Abbasi. Development of AZ91/SiC surface composite by FSP: effect of vibration and process parameters on microstructure and mechanical characteristics [J]. Advances in Manufacturing, 2020, 8(1): 82-96.
[11]	Muhammad Tariq, Ying Li, Wen-Xian Li, Zhong-Rui Yu, Jia-Mei Li, Ye-Min Hu, Ming-Yuan Zhu, Hong-Ming Jin, Yang Liu, Yi-Bing Li, Katerina Skotnicova. Structural, ferromagnetic, and optical properties of Fe and Al co-doped ZnO diluted magnetic semiconductor nanoparticles synthesized under high magnetic field [J]. Advances in Manufacturing, 2019, 7(2): 248-255.
[12]	Dong-Dong Chen, Yong-Cheng Lin, Xiao-Min Chen. A strategy to control microstructures of a Ni-based superalloy during hot forging based on particle swarm optimization algorithm [J]. Advances in Manufacturing, 2019, 7(2): 238-247.
[13]	Qin-Xiang Xia, Jin-Chuan Long, Ning-Yuan Zhu, Gang-Feng Xiao. Research on the microstructure evolution of Ni-based superalloy cylindrical parts during hot power spinning [J]. Advances in Manufacturing, 2019, 7(1): 52-63.
[14]	Ze-Xing Su, Chao-Yang Sun, Ming-Wang Fu, Ling-Yun Qian. Physical-based constitutive model considering the microstructure evolution during hot working of AZ80 magnesium alloy [J]. Advances in Manufacturing, 2019, 7(1): 30-41.
[15]	Jie Sun, Cheng Sheng, Ding-Pu Wang, Jing Zhao, Yun-Hu Zhang, Hong-Gang Zhong, Gui Wang, Qi-jie Zhai. Fine equiaxed dendritic structure of a medium carbon steel cast using pulsed magneto-oscillation melt treatment [J]. Advances in Manufacturing, 2018, 6(2): 189-194.