Development of AZ91/SiC surface composite by FSP: effect of vibration and process parameters on microstructure and mechanical characteristics

doi:10.1007/s40436-019-00288-9

Abstract

Abstract: A surface composite layer enhances the mechanical characteristics of a surface while retaining the properties of the base material. Friction stir processing (FSP) is a method for forming surface metal matrix composites (SMMCs) that reinforce a surface with particles. In the current study, a new method entitled friction stir vibration processing (FSVP) was applied to form SMMCs on the surface of AZ91 magnesium alloy with SiC particles as the reinforcing particles. Contrary to FSP, in FSVP, the workpiece was vibrated normal to the processing line while the tool rotated and traversed. The microstructure and mechanical properties of friction stir (FS) and friction stir vibration (FSV) processed specimens were evaluated. Additionally, the effects of vibration frequency and process parameters on different characteristics of FS and FSV processed specimens were studied. The results showed that the stir zone grains for FSV processed specimens were finer than those for FS processed specimens, and the second phase particles (SiC particles) had a more homogenous distribution in the former specimens than in the latter specimens. This was related to the effect of workpiece vibration during FSVP, which increased the material deformation and led to enhanced dynamic recrystallization and the breakdown of agglomerated SiC particles. The results indicated that the stir zone grain size decreased, and the distribution homogeneity of the SiC particles increased as vibration frequency increased. It was also observed that the stir zone grain size increased, and the mechanical properties of the processed specimens decreased as tool rotation speed increased.

The full text can be downloaded at https://link.springer.com/content/pdf/10.1007%2Fs40436-019-00288-9.pdf

Key words: Friction stir processing (FSP), Vibration, AZ91 magnesium alloy, Dynamic recrystallization, Microstructure, Mechanical properties

Behrouz Bagheri, Mahmoud Abbasi. Development of AZ91/SiC surface composite by FSP: effect of vibration and process parameters on microstructure and mechanical characteristics[J]. Advances in Manufacturing, 2020, 8(1): 82-96.

TrendMD

References

1. Abbasi M, Abdollahzadeh A, Omidvar H et al (2016) Incorporation of SiC particles in FS welded zone of AZ31 Mg alloy to improve the mechanical properties and corrosion resistance. J Mater Res 107:566-572
2. Abdollahzadeh A, Shokuhfar A, Omidvar H et al (2019) Structural evaluation and mechanical properties of AZ31/SiC nanocomposite produced by friction stir welding process at various welding speeds. Proc Inst Mech Eng Part L J Mater Des Appl 233:831-841
3. Abdollahzadeh A, Shokuhfar A, Cabrera JM et al (2019) In-situ nanocomposite in friction stir welding of 6061-T6 aluminum alloy to AZ31 magnesium alloy. J Mater Proc Technol 263:296-307
4. Abdollahzadeh A, Shokuhfar A, Cabrera JM et al (2018) The effect of changing chemical composition on dissimilar Mg/Al friction stir welded butt joints using zinc interlayer. J Manuf Proc 34:18-30
5. Segal VM (2004) Engineering and commercialization of equal channel angular extrusion. Mater Sci Eng A 386:269-276
6. Edalati K, Horita Z (2016) A review on high-pressure torsion (HPT) from 1935 to 1988. Mater Sci Eng A 652:325-352
7. Nunes LGS, Machado MLP (2018) Simulation of the accumulative roll-bonding process through warm torsion test. J Mater Res Technol 7:326-330
8. Barati M, Abbasi M, Abedini M (2019) The effects of friction stir processing and friction stir vibration processing on mechanical, wear and corrosion characteristics of Al6061/SiO₂ surface. J Manuf Process 45:491-497
9. Dadaei M, Omidvar H, Bagheri B et al (2014) The effect of SiC/Al₂O₃ particles used during FSP on mechanical properties of AZ91 magnesium alloy. J Mater Res 105:369-374
10. Zheng FY, Wu YJ, Peng LM et al (2013) Microstructure and mechanical properties of friction stir processed Mg-2.0Nd-0.3Zn-1.0Zr magnesium alloy. J Magnes Alloys 1:122-127
11. Chai F, Zhang D, Li Y (2014) Effect of thermal history on microstructures and mechanical properties of AZ31 magnesium alloy prepared by friction stir processing. Materials 7:1573-1589
12. Iwaszko J, Kudla K, Fila K (2016) Friction stir processing of the AZ91 magnesium alloy with SiC particles. Arch Mater Sci Eng 77:85-92
13. Asadi P, Faraji G, Besharati MK (2010) Producing of AZ91/SiC composite by friction stir processing. J Adv Manuf Technol 51:247-260
14. Abbasi M, Bagheri B, Dadaei M et al (2015) The effect of FSP on mechanical, tribological and corrosion behavior of composite layer developed on magnesium AZ91 alloy surface. Int J Adv Manuf Technol 77:2051-2058
15. ASTM-E3-11 (2017) Standard guide for preparation of metallographic specimens. Annual Book of ASTM Standards. American Society for Testing and Materials, West Conshohocken
16. ASTM-E8M (2016) Standard test methods for tension testing of metallic material. Annual Book of ASTM Standards. American Society for Testing and Materials, West Conshohocken
17. ASTM-E112-13 (2017) Standard test methods for determining average grain size. Annual Book of ASTM Standards. American Society for Testing and Materials, West Conshohocken
18. ASTM-E384-11 (2011) Standard test method for Knoop and Vickers hardness of materials. Annual Book of ASTM Standards. American Society for Testing and Materials, West Conshohocken
19. Abbasi M, Givi M, Ramazani A (2019) Friction stir vibration processing:a new method to improve the microstructure and mechanical properties of Al5052/SiC surface nano-composite layer. Int J Adv Manuf Technol 100:1463-1473
20. Kaibyshev R, Shipilova K, Musin F et al (2005) Continous dynamic recrystallization in an Al-Li-Mg-Sc alloy during equalchannel angular extrusion. Mater Sci Eng A 396:341-351
21. Darvishi Kamachali R, Steinbach I (2012) 3D phase-field simulation of grain growth:topological analysis versus mean-field approximates. Acta Mater 60:2719-2728
22. Fouladi S, Abbasi M (2017) The effect of friction stir vibration welding process on characteristics of SiO₂ incorporated joint. J Mater Process Technol 243:23-30
23. Hull D, Bacon DJ (2011) Introduction to dislocations. Butterworth-Heinemann, Britain
24. Naderi M, Abbasi M, Saeed-Akbari A (2013) Enhanced mechanical properties of a hot-stamped advanced high-strength steel via tempering treatment. Metall Mater Trans A 44:1852-1861
25. Callister WD (2003) Materials science and engineering:an introduction. Wiley, Hoboken
26. Estrin YZ, Zabrodin PA, Braude IS et al (2010) Low temperature plastic deformation of AZ31 magnesium alloy with different microstructures. Low Temper Phys 36:1100-1112
27. Barooni O, Abbasi M, Givi M et al (2017) New method to improve the microstructure and mechanical properties of joint obtained using FSW. Int J Adv Manuf Technol 93:4371-4378
28. Uthaisangsuk V (2009) Microstructure based formability modeling of multiphase steels. Dissertation, IEHK, RWTH-Aachen
29. Dieter GE, Bacon D (1988) Mechanical and metallurgy. McGraw-Hill, London
30. Hertzberg RW (1996) Deformation and Fracture mechanics of engineering materials, 4th edn. Wiley, Hoboken
31. Bagheri B, Mahdian Rizi AA, Abbasi M et al (2019) Friction stir spot vibration welding:improving the microstructure and mechanical properties of Al5083 joint. Metallogr Microstruct Anal 8:713-725
32. Li YS, Zhang Y, Tao NR et al (2009) Effect of the Zener-Hollomon parameter on the microstructures and mechanical properties of Cu subjected to plastic deformation. Acta Mater 57:761-772
33. Chang CI, Lee CJ, Huang JC (2004) Relationship between grain size and Zener-Holloman parameter during friction stir processing in AZ31 Mg alloys. Scr Mater 51:509-514
34. Starink MJ, Deschamps A, Wang SC (2008) The strength of friction stir welded and friction stir processed aluminium alloys. Scr Mater 58:377-382
35. Callister WD (2003) Materials science and engineering:an introduction. Wiley, Hoboken, pp 153-164

[1]	Xiao-Fen Liu, Wen-Hu Wang, Rui-Song Jiang, Yi-Feng Xiong, Kun-Yang Lin. Tool wear mechanisms in axial ultrasonic vibration assisted milling in-situ TiB₂/7050Al metal matrix composites [J]. Advances in Manufacturing, 2020, 8(2): 252-264.
[2]	Jun-Yun Chen, Tian-Ye Jin, Xi-Chun Luo. Key machining characteristics in ultrasonic vibration cutting of single crystal silicon for micro grooves [J]. Advances in Manufacturing, 2019, 7(3): 303-314.
[3]	Dong-Dong Chen, Yong-Cheng Lin, Xiao-Min Chen. A strategy to control microstructures of a Ni-based superalloy during hot forging based on particle swarm optimization algorithm [J]. Advances in Manufacturing, 2019, 7(2): 238-247.
[4]	Ze-Xing Su, Chao-Yang Sun, Ming-Wang Fu, Ling-Yun Qian. Physical-based constitutive model considering the microstructure evolution during hot working of AZ80 magnesium alloy [J]. Advances in Manufacturing, 2019, 7(1): 30-41.
[5]	Qin-Xiang Xia, Jin-Chuan Long, Ning-Yuan Zhu, Gang-Feng Xiao. Research on the microstructure evolution of Ni-based superalloy cylindrical parts during hot power spinning [J]. Advances in Manufacturing, 2019, 7(1): 52-63.
[6]	Michael Löser, Andreas Otto, Steffen Ihlenfeldt, Günter Radons. Chatter prediction for uncertain parameters [J]. Advances in Manufacturing, 2018, 6(3): 319-333.
[7]	Jie Sun, Cheng Sheng, Ding-Pu Wang, Jing Zhao, Yun-Hu Zhang, Hong-Gang Zhong, Gui Wang, Qi-jie Zhai. Fine equiaxed dendritic structure of a medium carbon steel cast using pulsed magneto-oscillation melt treatment [J]. Advances in Manufacturing, 2018, 6(2): 189-194.
[8]	Qiang He, An-Ling Li, Yuan Shen, Li-Li Li. Thermal optimization and experimental research of high-speed universal pulverizer [J]. Advances in Manufacturing, 2018, 6(1): 83-94.
[9]	Jyotirmoy Nandy, Hrushikesh Sarangi, Seshadev Sahoo. Microstructure evolution of Al-Si-10Mg in direct metal laser sintering using phase-field modeling [J]. Advances in Manufacturing, 2018, 6(1): 107-117.
[10]	Jian-Xin Lin, Xu-Ming Liu, Chuan-Wei Cui, Chuan-Yi Bai, Yu-Ming Lu, Feng Fan, Yan-Qun Guo, Zhi-Yong Liu, Chuan-Bing Cai. A review of thickness-induced evolutions of microstructure and superconducting performance of REBa₂Cu₃O_7-δ coated conductor [J]. Advances in Manufacturing, 2017, 5(2): 165-176.
[11]	Antonello Astarita, Mario Coppola, Sergio Esposito, Mariacira Liberini, Leandro Maio, Ilaria Papa, Fabio Scherillo, Antonino Squillace. Experimental characterization of Ti6Al4V T joints welded through linear friction welding technique: microstructure and NDE [J]. Advances in Manufacturing, 2016, 4(4): 305-313.
[12]	Prakash KumarSahu, Kanchan Kumari, Sukhomay Pal, Surjya K. Pal. Hybrid fuzzy-grey-Taguchi based multi weld quality optimization of Al/Cu dissimilar friction stir welded joints [J]. Advances in Manufacturing, 2016, 4(3): 237-247.
[13]	Shun-Li Zhao, Jun-Fei Fan, Jie-Yu Zhang, Kuo-Chih Chou, Hai-Rong Le. High speed steel produced by spray forming [J]. Advances in Manufacturing, 2016, 4(2): 115-122.
[14]	Wei-Xing Xu, Liang-Chi Zhang. Ultrasonic vibration-assisted machining: principle, design and application [J]. Advances in Manufacturing, 2015, 3(3): 173-192.
[15]	Omar A. Mohamed, Syed H. Masood, Jahar L. Bhowmik. Optimization of fused deposition modeling process parameters: a review of current research and future prospects [J]. Advances in Manufacturing, 2015, 3(1): 42-53.