Comparative investigation towards machinability improvement in hard turning using coated and uncoated carbide inserts: part I experimental investigation

doi:10.1007/s40436-018-0215-z

Abstract

Abstract:

The investigation of low cost uncoated and coated carbide insert in the hard turning of hardened AISI D2 steel (≥55 HRC) will definitely open up a new arena as an economical alternative suitable to industrial machining sectors. Thus, this paper reports the comparative machinability assessment for the hard turning of AISI D2 steel ((55 ±1) HRC) by coated and uncoated carbide insert in a dry environment. Micro hardness and abrasion tests were carried out to assess resistance capability against wear. The above test results confirmed the greater wear resistance ability of Al₂O₃ coated carbide insert over uncoated carbide. Based on the extensive investigation of comparative machinability, the coated carbide insert (TiN-TiCN-Al₂O₃) outperformed the uncoated carbide insert with regard to surface roughness, flank wear, chip-tool interface temperature, and chip morphology. Abrasion and diffusion were observed as the principal tool wear mechanisms in the investigated range. The uncoated carbide failed completely due to the severe chipping and quick dulling of the cutting edge, which led to its unsuitability for machining hardened steel.

The full text can be downloaded at https://link.springer.com/article/10.1007/s40436-018-0215-z

Key words: Coated and uncoated carbide, Hard turning, Machinability, Flank wear, Surface roughness, Chip morphology, Cutting temperature

Ramanuj Kumar, Ashok Kumar Sahoo, Purna Chandra Mishra, Rabin Kumar Das. Comparative investigation towards machinability improvement in hard turning using coated and uncoated carbide inserts: part I experimental investigation[J]. Advances in Manufacturing, 2018, 6(1): 52-70.

TrendMD

References

1. Davim JP (2008) Machining:fundamentals and recent advances. Springer, Berlin, p 97
2. Chinchanikar S, Choudhury SK (2015) Machining of hardened steel-experimental investigations, performance modeling and cooling techniques:a review. Int J Mach Tool Manuf 89:95-109
3. Sahoo AK, Sahoo B (2013) Performance studies of multilayer hard surface coatings (TiN/TiCN/Al₂O₃/TiN) of indexable carbide inserts in hard machining:part-I (an experimental approach). Measurement 46:2854-2867
4. Junior CADO, Diniz AE, Bertazzoli R (2014) Correlating tool wear, surface roughness and corrosion resistance in the turning process of super duplex stainless steel. J Braz Soc Mech Sci Eng 36:775-785
5. Sharma J, Sidhu BS (2014) Investigation of effects of dry and near dry machining on AISI D2 steel using vegetable oil. J Clean Prod 66:619-623
6. Chen T, Li S, Han B et al (2014) Study on cutting force and surface micro-topography of hard turning of GCr15 steel. Int J Adv Manuf Technol 72:1639-1645
7. Jiang F, Yan L, Rong Y (2013) Orthogonal cutting of hardened AISI D2 steel with TiAlN-coated inserts-simulations and experiments. Int J Adv Manuf Technol 64:1555-1563
8. Sahoo AK, Sahoo B (2013) Comparative study on performance of multilayer coated and uncoated carbide inserts when turning AISI D2 steel under dry environment. Measurement 46:2695-2704
9. Shalaby MA, Hakim MAE, Abdelhameed MM et al (2014) Wear mechanisms of several cutting tool materials in hard turning of high carbon-chromium tool steel. Tribol Int 70(2):148-154
10. Dosbaeva GK, Hakim MAE, Shalaby MA et al (2015) Cutting temperature effect on PCBN and CVD coated carbide tools in hard turning of D2 tool steel. Int J Refract Met Hard Mater 50:1-8
11. Das SR, Dhupal D, Kumar A (2015) Experimental investigation into machinability of hardened AISI 4140 steel using TiN coated ceramic tool. Measurement 62:108-126
12. Ferreira R, Carou D, Lauro CH et al (2016) Surface roughness investigation in the hard turning of steel using ceramic tools. Mater Manuf Process 31(5):648-652
13. Melo ACA, Milan JCG, Da Silva MB et al (2006) Some observations on wear and damages in cemented carbide tools. J Braz Soc Mech Sci Eng 28(3):269-277
14. Pal A, Choudhury SK, Chinchanikar S (2014) Machinability assessment through experimental investigation during hard and soft turning of hardened steel. Procedia Mater Sci 6(6):80-91
15. Kagnaya T, Boher C, Lambert L et al (2014) Microstructural analysis of wear micro mechanisms of WC-6Co cutting tools during high speed dry machining. Int J Refract Met Hard Mater 42(42):151-162
16. Sahu SK, Mishra PC, Orra K et al (2015) Performance assessment in hard turning of AISI 1015 steel under spray impingement cooling and dry environment. Proc IMechE Part B J Eng Manuf 229(2):251-265
17. Chinchanikar S, Choudhury SK (2013) Investigations on machinability aspects of hardened AISI 4340 steel at different levels of hardness using coated carbide tools. Int J Refract Met Hard Mater 38(3):124-133
18. Mhamdi MB, Salem SB, Boujelbene M et al (2013) Experimental study of the chip morphology in turning hardened AISI D2 steel. J Mech Sci Technol 27(11):3451-3461
19. Salem SB, Bayraktar E, Boujelbene M et al (2012) Effect of cutting parameters on chip formation in orthogonal cutting. J Achiev Mater Manuf Eng 50(1):1101-1106
20. Basak S, Davim JP (2007) Application of radial basis function neural networks in optimization of hard turning of AISI D2 coldworked tool steel with a ceramic tool. Proc IMechE Part B J Eng Manuf 737:987-998
21. Davim JP, Figueira L (2007) Comparative evaluation of conventional and wiper ceramic tools on cutting forces, surface roughness, and tool wear in hard turning AISI D2 steel. Proc IMechE Part B J Eng Manuf 762:625-633
22. Bensouilah H, Aouici H, Meddour I et al (2016) Performance of coated and uncoated mixed ceramic tools in hard turning process. Measurement 82:1-18
23. Das A, Mukhopadhyay A, Patel SK et al (2016) Comparative assessment on machinability aspects of AISI 4340 alloy steel using uncoated carbide and coated cermet inserts during hard turning. Arab J Sci Eng 41(11):4531-4552
24. Yallese MA, Chaoui K, Zeghib N et al (2009) Hard machining of hardened bearing steel using cubic boron nitride tool. J Mater Process Technol 209(2):1092-1104
25. Gaitonde VN, Karnik SR, Figueira L et al (2009) Machinability investigations in hard turning of AISI D2 cold work tool steel with conventional and wiper ceramic inserts. Int J Refract Met Hard Mater 27(4):754-763
26. Ferreira R, Rehor J, Lauro CH et al (2016) Analysis of the hard turning of AISI H13 steel with ceramic tools based on tool geometry:surface roughness, tool wear and their relation. J Braz Soc Mech Sci Eng 38(8):2413-2420
27. Suresh R, Basavarajappa S, Samuel GL (2012) Some studies on hard turning of AISI 4340 steel using multilayer coated carbide tool. Measurement 45(7):1872-1884
28. Suresh R, Basavarajappa S, Gaitonde VN et al (2012) Machinability investigations on hardened AISI 4340 steel using coated carbide insert. Int J Refract Met Hard Mater 33(1):75-86
29. Asilturk I·, Akkus H (2011) Determining the effect of cutting parameters on surface roughness in hard turning using the Taguchi method. Measurement 44(9):1697-1704
30. Tang L, Huang J, Xie L (2011) Finite element modeling and simulation in dry hard orthogonal cutting AISI D2 tool steel with CBN cutting tool. Int J Adv Manuf Technol 53(9-12):1167-1181
31. Aslantas K, Ucun I·, Cicek A (2012) Tool life and wear mechanism of coated and uncoated Al₂O₃/TiCN mixed ceramic tools in turning hardened alloy steel. Wear 274-275(3):442-451
32. Lim CYH, Lim SC, Lee KS (1999) Wear of TiC-coated carbide tools in dry turning. Wear 225-229(225):354-367
33. Sahoo AK (2013) Experimental investigation on flank wear and tool life, cost analysis and mathematical model in turning hardened steel using coated carbide inserts. Int J Ind Eng Comput 4(4):571-578
34. Sahoo AK, Mishra PC (2014) A response surface methodology and desirability approach for predictive modelling and optimization of cutting temperature in machining hardened steel. Int J Ind Eng Comput 5(3):407-416
35. Davim JP, Figueira L (2007) Machinability evaluation in hard turning of cold work tool steel (D2) with ceramic tools using statistical techniques. Mater Des 28:1186-1191
36. Gaitonde VN, Karnik SR, Figueira L et al (2011) Performance comparison of conventional and wiper ceramic inserts in hard turning through artificial neural network modelling. Int J Adv Manuf Technol 52(1-4):101-114
37. Gaitonde VN, Karnik SR, Figueira L et al (2009) Analysis of machinability during hard turning of cold work tool steel (type:AISI D2). Mater Manuf Process 24(12):1373-1382
38. Quiza R, Figueira L, Davim JP (2008) Comparing statistical models and artificial neural networks on predicting the tool wear in hard machining D2 AISI steel. Int J Adv Manuf Technol 37:641-648
39. Bhattacharya A, Das S, Majumder P et al (2009) Estimating the effect of cutting parameters on surface finish and power consumption during high speed machining of AISI 1045 steel using Taguchi design and ANOVA. Prod Eng Res Dev 3(1):31-40
40. More AS, Jiang W, Brown WD et al (2006) Tool wear and machining performance of CBN-TiN coated carbide inserts and PCBN compact inserts in turning AISI 4340 hardened steel. J Mater Process Technol 180(1-3):253-262
41. Kamdi Z, Shipway PH, Voisey KT et al (2011) Abrasive wear behaviour of conventional and large-particle tungsten carbidebased cermet coatings as a function of abrasive size and type. Wear 271(9):1264-1272
42. Nahvi SM, Shipway PH, McCartney DG (2009) Particle motion and modes of wear in the dry sand-rubber wheel abrasion test. Wear 267(11):2083-2091
43. Özel T, Altan T (2000) Determination of workpiece flow stress and friction at the chip-tool contact for high-speed cutting. Int J Mach Tools Manuf 40(1):133-152
44. Sahoo AK, Sahoo B (2013) A comparative study on performance of multilayer coated and uncoated carbide inserts when turning AISI D2 steel under dry environment. Measurement 46(8):2695-2704
45. Shaw MC, Vyas A (1998) The mechanism of chip formation with hard turning steel. CIRP Ann Manuf Technol 47(1):77-82
46. EI-Wardany TI, Kishawy HA, Elbestawi MA (2000) Surface integrity of die material in high speed hard machining, part-1:micrographical analysis. J Manuf Sci & Eng 122(4):620-631
47. Davim JP (2011) Machining of hard materials. Springer, Berlin, pp 99-100
48. Pramanik A, Zhang LC (2017) Particle fracture and debonding during orthogonal machining of metal matrix composites. Adv Manuf 5(1):77-82
49. Sahoo AK, Sahoo AK, Mohanty T et al (2013) Optimization of multiple performance characteristics in turning using Taguchi's quality loss function:an experimental investigation. Int J Ind Eng Comput 4(3):325-336

[1]	Wei Zhao, Asif Iqbal, Ding Fang, Ning He, Qi Yang. Experimental study on the meso-scale milling of tungsten carbide WC-17.5Co with PCD end mills [J]. Advances in Manufacturing, 2020, 8(2): 230-241.
[2]	Xiao-Guang Guo, Ming Li, Zhi-Gang Dong, Rui-Feng Zhai, Zhu-Ji Jin, Ren-Ke Kang. Smooth particle hydrodynamics modeling of cutting force in milling process of TC4 [J]. Advances in Manufacturing, 2019, 7(4): 364-373.
[3]	Ali Kalyon, Mustafa Günay, Dursun Özyürek. Application of grey relational analysis based on Taguchi method for optimizing machining parameters in hard turning of high chrome cast iron [J]. Advances in Manufacturing, 2018, 6(4): 419-429.
[4]	Ramanuj Kumar, Ashok Kumar Sahoo, Purna Chandra Mishra, Rabin Kumar Das. Comparative study on machinability improvement in hard turning using coated and uncoated carbide inserts: part II modeling, multi-response optimization, tool life, and economic aspects [J]. Advances in Manufacturing, 2018, 6(2): 155-175.
[5]	Mohammad Lotfi, Saeid Amini, Ihsan Yaseen Al-Awady. 3D numerical analysis of drilling process: heat, wear, and built-up edge [J]. Advances in Manufacturing, 2018, 6(2): 204-214.
[6]	Ravindra Nath Yadav. Development and experimental investigation of duplex turning process [J]. Advances in Manufacturing, 2017, 5(2): 149-157.
[7]	A. Pramanik, A. R. Dixit, S. Chattopadhyaya, M. S. Uddin, Yu Dong, A. K. Basak, G. Littlefair. Fatigue life of machined components [J]. Advances in Manufacturing, 2017, 5(1): 59-76.
[8]	Vedat Savas, Cetin Ozay, Hasan Ballikaya. Experimental investigation of cutting parameters in machining of 100Cr6 with tangential turn-milling method [J]. Advances in Manufacturing, 2016, 4(1): 97-104.
[9]	Varaprasad Bhemuni, Srinivasa Rao Chalamalasetti, Pavan Kumar Konchada, Venkata Vinay Pragada. Analysis of hard turning process: thermal aspects [J]. Advances in Manufacturing, 2015, 3(4): 323-330.
[10]	Satyanarayana Kosaraju Venu Gopal Anne. Optimal machining conditions for turning Ti-6Al-4V using response surface methodology [J]. Advances in Manufacturing, 2013, 1(4): 329-339.