Turning of aluminum metal matrix composites: influence of the reinforcement and the cutting condition on the surface layer of the workpiece

doi:10.1007/s40436-016-0152-7

Abstract

Abstract:

Aluminum metal matrix composites (Al-MMCs) are difficult to machine. The reinforcement of aluminum using ceramic particles accelerates tool wear. Moreover, demanded machining accuracies or properties of the surface layer are difficult to achieve. In the present study, the effect of silicon carbide reinforcement particles on the surface layer of the workpiece was investigated using multiple cutting conditions for dry turning. Three differently reinforced Al-MMCs regarding the volume percentage (17% and 30%) and the particle size (0.6 μm and 3 μm) and their non-reinforced matrix were considered as the workpiece materials. The reinforcement and the cutting condition affect the results of turning. A greater particle volume percent improves the surface roughness and decreases the tensile stress in the surface. The smaller particle size caused a lower tensile stress in the surface. A general effect of the particle size on the workpiece roughness can not be concluded. The most important cutting parameter for the surface layer of the workpiece is the feed. Greater feeds decrease the tensile stress in the surface, but deteriorate the surface quality.

Key words: Aluminum metal matrix composite (Al-MMC), Forces, Workpiece roughness, Surface, Residual stress

Jan C. Aurich, Marco Zimmermann, Stefan Schindler, Paul Steinmann. Turning of aluminum metal matrix composites: influence of the reinforcement and the cutting condition on the surface layer of the workpiece[J]. Advances in Manufacturing, 2016, 4(3): 225-236.

TrendMD

Add to citation manager EndNote|Reference Manager|ProCite|BibTeX|RefWorks

URL: https://www.aim.shu.edu.cn/EN/10.1007/s40436-016-0152-7

https://www.aim.shu.edu.cn/EN/Y2016/V4/I3/225

References

1. Bian R, He N, Li L et al (2014) Precision milling of high volume fraction SiCp/Al composites with monocrystalline diamond end mill. Int J Adv Manuf Technol 71(1-4):411-419
2. Tomac N, Tonnessen K (1992) Machinability of particulate aluminium matrix composites. CIRP Ann Manuf Technol 42(1):55-58
3. Wang T, Xie L, Wang X et al (2015) PCD tool performance in high-speed milling of high volume fraction SiCp/Al composites. Int J Adv Manuf Technol 78(9):1445-1453
4. Pramanik A, Zhang LC, Arsecularatne JA (2008) Machining of metal matrix composites:effect of ceramic particles on residual stress, surface roughness and chip formation. Int J Mach Tool Manuf 48(15):1613-1625
5. Aurich JC, Zimmermann M, Schindler S et al (2016) Effect of the cutting condition and the reinforcement phase on the thermal load of the workpiece when dry turning aluminum metal matrix composites. Int J Adv Manuf Technol 82(5):1317-1334
6. Yang Y, Wu Q, Zhan Z et al (2015) An experimental study on milling of high-volume fraction SiCp/Al composites with PCD tools of different grain size. Int J Adv Manuf Technol 79(9):1699-1705
7. El-Gallab M, Sklad M (1998) Machining of Al/SiC particulate metal-matrix composites Part I:tool performance. J Mater Process Technol 83(1-3):151-158
8. Shahzad MA (2010) Analysis of the machinability of an aluminum matrix composite material. Dissertation, University of Kaiserslautern
9. Wang T, Xie L, Wang X (2015) Simulation study on defect formation mechanism of the machined surface in milling of high volume fraction SiCp/Al composite. Int J Adv Manuf Technol 79(5):1185-1194
10. Ge YF, Xu JH, Yang H et al (2008) Workpiece surface quality when ultra-precision turning of SiCp/Al composites. J Mater Process Technol 203(1-3):166-175
11. El-Gallab M, Sklad M (1998) Machining of Al/SiC particulate metal matrix composites. Part Ⅱ:workpiece surface integrity. J Mater Process Technol 83(1-3):277-285
12. Cheung CF, Chan KC, To S et al (2002) Effect of reinforcement in ultra-precision machining of Al6061/SiC metal matrix composites. Scripta Mater 47(2):77-82
13. Kilickap E, Cakir O, Aksoy M et al (2005) Study of tool wear and surface roughness in machining of homogenized SiCp reinforced aluminium metal matrix composite. J Mater Process Technol 164-165:862-867
14. Teti R (2002) Machining of composite materials. CIRP Ann Manuf Technol 51(2):611-634
15. Dabade UA, Joshi SS, Balasubramaniam R et al (2007) Surface finish and integrity of machined surfaces on Al/SiCp composites. J Mater Process Technol 192-193:166-174
16. Quan Y, Ye B (2003) The effect of machining on the surface properties of SiC/Al composites. J Mater Process Technol 138(1-3):464-467
17. Schindler S, Zimmermann M, Aurich JC et al (2014) Thermoelastic deformations of the workpiece when dry turning aluminum alloys-a finite element model to predict thermal effects in the workpiece. CIRP J Manuf Sci Technol 7(3):233-245
18. Sikder S, Kishawy HA (2012) Analytical model for force prediction when machining metal matrix composite. Int J Mech Sci 59(1):95-103
19. Dabade UA, Dapkekar D, Joshi SS (2009) Modeling of chip-tool interface friction to predict cutting forces in machining of Al/SiCp composites. Intern J Mach Tool Manuf 49(9):690-700
20. Klocke F, König W (2008) Fertigungsverfahren, Drehen, Fräsen, Bohren. Springer, Berlin
21. Karthikeyan R, Ganesan G, Nagarazan RS et al (2001) A critical study on machining of Al/SiC composites. Mater Manuf Process 16(1):47-60
22. Nakayama K, Arai M, Kanda T (1988) Machining characteristics of hard materials. CIRP Ann Manuf Technol 37(1):89-92
23. Schulze V, Zanger F, Michna J et al (2011) Investigation of the machining behavior of metal matrix composites (MMC) using chip formation simulation. Adv Mat Res 223:20-29
24. Denkena B, Biermann D (2014) Cutting edge geometries. CIRP Ann Manuf Technol 63(2):631-653
25. Biermann D (1995) Untersuchungen zum Drehen von Aluminiummatrix-Verbundwerkstoffen. Dissertation, University of Dortmund
26. Capello E (2005) Residual stresses in turning Part Ⅰ:influence of the process parameters. J Mater Process Technol 160(2):221-228
27. Breidenstein B (2011) Oberflächen und Randzonen hoch belasteter Bauteile. Dissertation, University of Hannover, Habilitation

[1]	Zhen Zhu, Bing-Zhou Xu, Chang-Qing Shen, Xiao-Jian Zhang, Si-Jie Yan, Han Ding. Complete coverage path planning for multi-connected free-form surface grinding based on reinforcement learning [J]. Advances in Manufacturing, 2026, 14(2): 359-376.
[2]	Yan-Jun Lu, Ming-Rong Guo, Yong-Qi Dai, Qiang Wang, Hu Luo. Experimental study on ultrasonic vibration-assisted grinding of quartz glass microchannel [J]. Advances in Manufacturing, 2025, 13(4): 701-717.
[3]	Guan-Yan Ge, Yu-Kun Xiao, Jun Lv, Zheng-Chun Du. Mechanism analysis and suppression for chatter and surface location error induced by error compensation [J]. Advances in Manufacturing, 2025, 13(4): 750-767.
[4]	Yong-Hao Zhou, Bin Shen, Lin Chang, Sergiy Valyukh, Ying-Jie Yu. Simultaneous precise measurements of multiple surfaces in wavelength-tuning interferometry via parameter estimation [J]. Advances in Manufacturing, 2025, 13(4): 768-783.
[5]	Lin Gu, Ke-Lin Li, Xiao-Ka Wang, Guo-Jian He. The effect of the slope angle and the magnetic field on the surface quality of nickel-based superalloys in blasting erosion arc machining [J]. Advances in Manufacturing, 2025, 13(3): 620-633.
[6]	Zhen-Jing Duan, Shuai-Shuai Wang, Shu-Yan Shi, Ji-Yu Liu, Yu-Heng Li, Zi-Heng Wang, Chang-He Li, Yu-Yang Zhou, Jin-Long Song, Xin Liu. Surface quality evaluation of cold plasma and NMQL multi-field coupling eco-friendly micro-milling 7075-T6 aluminum alloy [J]. Advances in Manufacturing, 2025, 13(1): 69-87.
[7]	Xiao-Fei Lei, Wen-Feng Ding, Biao Zhao, Dao-Hui Xiang, Zi-Ang Liu, Chuan Qian, Qi Liu, Dong-Dong Xu, Yan-Jun Zhao, Jian-Hui Zhu. Surface roughness model of ultrasonic vibration-assisted grinding GCr15SiMn bearing steel and surface topography evaluation [J]. Advances in Manufacturing, 2025, 13(1): 88-104.
[8]	Xin Wang, Qing-Liao He, Biao Zhao, Wen-Feng Ding, Qi Liu, Dong-Dong Xu. Effects of tool coating and tool wear on the surface and chip morphology in side milling of Ti₂AlNb intermetallic alloys [J]. Advances in Manufacturing, 2025, 13(1): 155-166.
[9]	Jia-Heng Zeng, Quan-Li Zhang, Yu-Can Fu, Jiu-Hua Xu. Heterogeneous ablation behavior of SiC_f/SiC composite by nanosecond pulse laser [J]. Advances in Manufacturing, 2025, 13(1): 196-210.
[10]	Jia-Hao Liu, Dong-Zhou Jia, Chang-He Li, Yan-Bin Zhang, Ying Fu, Zhen-Lin Lv, Shuo Feng. Mechanism and machinability in novel electroplastic-assisted grinding ductile iron [J]. Advances in Manufacturing, 2025, 13(1): 245-263.
[11]	Tuhin Kar, Swarup S. Deshmukh, Arjyajyoti Goswami. Fabrication of micro holes using low power fiber laser: surface morphology, modeling and soft-computing based optimization [J]. Advances in Manufacturing, 2024, 12(4): 810-831.
[12]	Yuan-Zhe Hu, Ru-Xue Liu, Jia-Peng He, Guo-Wei Zhou, Da-Yong Li. Deep learning methods for roping defect analysis in aluminum alloy sheets: prediction and grading [J]. Advances in Manufacturing, 2024, 12(3): 576-590.
[13]	Qiang Gao, Ya-Ou Zhang, Xue-Cheng Xi, Yuan-Ding Wang, Xiao-Fei Chen, Wan-Sheng Zhao. Research on feed-pulse collaborative control method in micro-electrical discharge machining [J]. Advances in Manufacturing, 2024, 12(2): 270-287.
[14]	Zhao-Qing Zhang, Kai-Ning Shi, Yao-Yao Shi, Yi-Hui Song, Zhe He, Ya-Song Pu. Study on a probabilistic algorithm for the forming and 3D characterization of special-shaped surfaces under profile grinding [J]. Advances in Manufacturing, 2024, 12(2): 288-299.
[15]	Jin Zhang, Li Ling, Qian-Yue Wang, Xue-Feng Huang, Xin-Zhen Kang, Gui-Bao Tao, Hua-Jun Cao. Surface quality investigation in high-speed dry milling of Ti-6Al-4V by using 2D ultrasonic-vibration-assisted milling platform [J]. Advances in Manufacturing, 2024, 12(2): 349-364.