Effects of process parameters on periodic impact force exerting on cutting tool in ultrasonic vibration-assisted oblique turning

doi:10.1007/s40436-022-00398-x

Abstract

Abstract: During ultrasonic vibration-assisted machining, the large impact force induced by tool-workpiece reengagement (TWR) is an important factor that affects tool chipping. However, mechanical analysis into process factors that affect the impact force and their influencing mechanisms are insufficient. Herein, a prediction model for the instantaneous cutting force during both TWR and the stable turning process, which depends on the process parameters and material properties, is firstly proposed based on the kinematic and dynamic analysis of ultrasonic vibration-assisted oblique turning (UVAOT). The results calculated using the developed cutting force model agree well with the experimental results presented in the literature. Next, the linear change law of the instantaneous cutting force with cutting time during the actual TWR is clarified using the proposed model. The effect of the UVAOT process parameters on the average impact force during the periodic TWR process is discussed, and the influence mechanism is analyzed from the perspective of mechanics. A positive linear correlation is discovered between the feed speed and average impact force. The ultrasonic amplitude and cutting speed do not significantly affect the average impact force of the new sharp cutting tools. These findings are consistent with the experimental observations of tool chipping and are applicable to select process parameters for reducing tool chipping during UVAOT.

The full text can be downloaded at https://link.springer.com/article/10.1007/s40436-022-00398-x

Key words: Kinematics, Dynamics, Ultrasonic vibrationassisted oblique turning (UVAOT), Impact force, Cutting force

Long-Xu Yao, Zhan-Qiang Liu, Qing-Hua Song, Bing Wang, Yu-Kui Cai. Effects of process parameters on periodic impact force exerting on cutting tool in ultrasonic vibration-assisted oblique turning[J]. Advances in Manufacturing, 2022, 10(3): 411-427.

TrendMD

Add to citation manager EndNote|Reference Manager|ProCite|BibTeX|RefWorks

URL: https://www.aim.shu.edu.cn/EN/10.1007/s40436-022-00398-x

https://www.aim.shu.edu.cn/EN/Y2022/V10/I3/411

1. Shamoto E, Altintas Y (1999) Prediction of shear angle in oblique cutting with maximum shear stress and minimum energy principles. Trans ASME J Manuf Sci Eng 121:399-407
2. Moufki A, Dudzinski D, Molinari A et al (2000) Thermoviscoplastic modelling of oblique cutting:forces and chip flow predictions. Int J Mech Sci 42(6):1205-1232
3. Moufki A, Devillez A, Dudzinski D et al (2004) Thermomechanical modelling of oblique cutting and experimental validation. Int J Mach Tools Manuf 44(9):971-989
4. Nath C, Rahman M (2008) Effect of machining parameters in ultrasonic vibration cutting. Int J Mach Tools Manuf 48(9):965-974
5. Xu Y, Wan Z, Zou P et al (2021) Experimental study on cutting force in ultrasonic vibration-assisted turning of 304 austenitic stainless steel. Proc Inst Mech Eng Part B J Eng Manuf 235(3):494-513
6. Teimouri R, Amini S, Mohagheghian N (2017) Experimental study and empirical analysis on effect of ultrasonic vibration during rotary turning of aluminum 7075 aerospace alloy. J Manuf Process 26:1-12
7. Liu CS, Zhao B, Gao GF et al (2002) Research on the characteristics of the cutting force in the vibration cutting of a particlereinforced metal matrix composites SiCp/Al. J Mater Process Technol 129(1/3):196-199
8. Gholamzadeh B, Soleimanimehr H (2019) Finite element modeling of ultrasonic-assisted turning:cutting force and heat generation. Mach Sci Technol 23(6):869-885
9. Muhammad R, Ahmed N, Roy A et al (2012) Numerical modelling of vibration-assisted turning of Ti-15333. Procedia CIRP 1:347-352
10. Zhang X, Kumar AS, Rahman M et al (2012) An analytical force model for orthogonal elliptical vibration cutting technique. J Manuf Process 14(3):378-387
11. Bai W, Sun R, Gao Y et al (2016) Analysis and modeling of force in orthogonal elliptical vibration cutting. Int J Adv Manuf Technol 83(5/8):1025-1036
12. Zhang C, Ehmann K, Li Y (2015) Analysis of cutting forces in the ultrasonic elliptical vibration-assisted micro-groove turning process. Int J Adv Manuf Technol 78(1/4):139-152
13. Nategh M, Razavi H, Abdullah A (2012) Analytical modeling and experimental investigation of ultrasonic-vibration assisted oblique turning, part I:kinematics analysis. Int J Mech Sci 63(1):1-11
14. Razavi H, Nategh M, Abdullah A (2012) Analytical modeling and experimental investigation of ultrasonic-vibration assisted oblique turning, part II:dynamics analysis. Int J Mech Sci 63(1):12-25
15. Razavi H, Nategh M, Abdullah A (2012) Analytical modeling and experimental investigation of ultrasonic-vibration assisted oblique turning, part III:experimental investigation. Int J Mech Sci 63(1):26-36
16. Lin J, Han J, Zhou X et al (2016) Study on predictive model of cutting force and geometry parameters for oblique elliptical vibration cutting. Int J Mech Sci 117:43-52
17. Liu J, Jiang X, Han X et al (2019) Influence of parameter matching on performance of high-speed rotary ultrasonic elliptical vibration-assisted machining for side milling of titanium alloys. Int J Adv Manuf Technol 101(5):1333-1348
18. Arrazola PJ, Özel T, Umbrello D et al (2013) Recent advances in modelling of metal machining processes. CIRP Ann 62(2):695-718
19. Fatima A, Mativenga PT (2013) A review of tool-chip contact length models in machining and future direction for improvement. Proc Inst Mech Eng Part B J Eng Manuf 227(3):345-356
20. Toropov A, Ko SL (2003) Prediction of tool-chip contact length using a new slip-line solution for orthogonal cutting. Int J Mach Tools Manuf 43(12):1209-1215
21. Pham TH, Nguyen DT, Banh TL et al (2020) Experimental study on the chip morphology, tool-chip contact length, workpiece vibration, and surface roughness during high-speed face milling of A6061 aluminum alloy. Proc Inst Mech Eng Part B:J Eng Manuf 234(3):610-620
22. Iqbal S, Mativenga P, Sheikh M (2009) A comparative study of the tool-chip contact length in turning of two engineering alloys for a wide range of cutting speeds. Int J Adv Manuf Technol 42(1/2):30-40
23. Brown R, Armarego E (1964) Oblique machining with a single cutting edge. Int J Mach Tool Des Res 4(1):9-25
24. Liu Y, Liu Z, Wang X et al (2020) Experimental study on tool wear in ultrasonic vibration-assisted milling of C/SiC composites. Int J Adv Manuf Technol 107(1):425-436

[1]	Fan Cui, Yu-Fei Gao, Da-Meng Cheng, Hong-Hao Li. Properties of cutting force, surface roughness and waviness in diamond wire sawing marble [J]. Advances in Manufacturing, 2026, 14(3): 674-696.
[2]	Bo-Wen Song, Da-Wei Zhang, Xiu-Bing Jing, Ying-Ying Ren, Yun Chen, Huai-Zhong Li. Enhanced cutting force model in micro-milling incorporating material separation criterion [J]. Advances in Manufacturing, 2025, 13(4): 813-830.
[3]	Yi-Fan Li, Liang-Chi Zhang. Role of interatomic potentials in molecular dynamics simulations of silicon nanomachining [J]. Advances in Manufacturing, 2025, 13(2): 265-283.
[4]	Chao-Jun Zhang, Song-Qing Li, Pei-Xuan Zhong, Fei-Fan Zhang, Wen-Jun Deng. Cutting performance and effectiveness evaluation on organic monolayer embrittlement in ductile metal precision machining [J]. Advances in Manufacturing, 2025, 13(2): 395-412.
[5]	Sheng Cai, Zhi-Chao Deng, Jia-Nan Wang, Nan Zhang. Dissimilar metals welding processes realized by vaporizing metal foils [J]. Advances in Manufacturing, 2025, 13(2): 430-443.
[6]	Cheng Fan, Cao-Yang Xue, Jun Zhao, Wei Jiang, Wen-Ge Han, Lei Zhang, Li-Ning Sun. Process planning and contour-based error compensation for precision grinding of miniature scalpels [J]. Advances in Manufacturing, 2024, 12(1): 108-123.
[7]	Guo-Liang Liu, Jin-Tao Zheng, Chuan-Zhen Huang, Shu-Feng Sun, Xin-Fu Liu, Long-Jie Dai, De-Xiang Wang, Xiang-Yu Wang. Coupling effect of micro-textured tools and cooling conditions on the turning performance of aluminum alloy 6061 [J]. Advances in Manufacturing, 2023, 11(4): 663-681.
[8]	Zhi-Fu Xue, Min Lai, Fei-Fei Xu, Feng-Zhou Fang. Molecular dynamics study on surface formation and phase transformation in nanometric cutting of β-Sn [J]. Advances in Manufacturing, 2022, 10(3): 356-367.
[9]	Bing Cao, Guo-Long Li, Alessandro Fortunato, Heng-Xin Ni. Continuous generating grinding method for beveloid gears and analysis of grinding characteristics [J]. Advances in Manufacturing, 2022, 10(3): 459-478.
[10]	Ming-Xian Xu, Liang-Shan Xiong, Bao-Yi Zhu, Ling-Feng Zheng, Kai Yin. Experimental research on the critical conditions and critical equation of chip splitting when turning a C45E4 disc workpiece symmetrically with a high-speed steel double-edged turning tool [J]. Advances in Manufacturing, 2022, 10(2): 159-174.
[11]	Ekrem Oezkaya, Sebastian Michel, Dirk Biermann. Experimental and computational analysis of the coolant distribution considering the viscosity of the cutting fluid during machining with helical deep hole drills [J]. Advances in Manufacturing, 2022, 10(2): 235-249.
[12]	Hao-Jie An, Jin-Shi Wang, Feng-Zhou Fang. Material removal at atomic and close-to-atomic scale by high-energy photon:a case study using atomistic-continuum method [J]. Advances in Manufacturing, 2022, 10(1): 59-71.
[13]	Kai-Ning Shi, Ning Liu, Cong-Le Liu, Jun-Xue Ren, Shan-Shan Yang, Wei Chit Tan. Indirect approach for predicting cutting force coefficients and power consumption in milling process [J]. Advances in Manufacturing, 2022, 10(1): 101-113.
[14]	Joseck Nyaboro, Mahmoud Ahmed, Hassan El-Hofy, Mohamed El-Hofy. Experimental and numerical investigation of the abrasive waterjet machining of aluminum-7075-T6 for aerospace applications [J]. Advances in Manufacturing, 2021, 9(2): 286-303.
[15]	Wei Zhao, Asif Iqbal, Ding Fang, Ning He, Qi Yang. Experimental study on the meso-scale milling of tungsten carbide WC-17.5Co with PCD end mills [J]. Advances in Manufacturing, 2020, 8(2): 230-241.

Effects of process parameters on periodic impact force exerting on cutting tool in ultrasonic vibration-assisted oblique turning

PDF

Knowledge

Abstract

Cite this article

share this article

Related Articles 15

Recommended Articles

Metrics

Comments